Electrical Safety - Jacuzzi sasha Vorinstallationsblatt

Some models allow you to connect the appliance to an alarm
circuit (provided, in the area marked with the bell symbol), a
bipolar cable with characteristics not inferior to type H 05 VV-F
2x2.5 mm 2 (220-240V - 2A max.); this cable must be used in order
to ensure that the cable clamp attached to the box offers ad-
equate protection (water tight) as detailed by legislation.
Audio system
The modules "sauna" and/or "hammam" are equipped with
speakers which are connected to a cable radio network; the rel-
evant cable must be arranged as indicated in position 3.
Upon request, an audio kit is available, which can be installed in
the appliance's appropriate equipment zone, to which the speak-
ers will also be connected.
NOTE:
- In the modules "sauna + hammam" or "sauna + shower +
hammam" the cable linked to the cable radio can be installed in
one of two positions indicated in the pre-installation instructions.
- "sauna", "hammam", "sauna+shower" and "sauna+ ham-
mam" two speakers; impedance: 4 Ω - optimal power: 20 W x2.
- "sauna+hammam", "sauna+shower+hammam"
four speakers; impedance: 8 Ω - optimal power: 20 W x 4.
Remote control system arrangement (where present)
it is possible to manage the "sauna" and "hammam" module
functions using a computer which interfaces with a remote con-
trol system (sc) via an Ethernet (LAN) network:
sc
it is also possible yo use a smartphone or tablet computer,
which interfaces via a wireless network (WLAN/Wi-Fi):
sc
sim
In any case, you must use an Ethernet socket (RJ-45), as indicated
in position 8, to which the cable (length: ~ 5 m) coming from the
remote control system, must be connected.
LAN
SMS
wi-fi
The remote control system (to be installed in the appliance
equipment zone) allows for the management of a maximum of
10 modules (max. 5 saunas and max. 5 hammams).
The cable connecting one module to another must not be longer
than 500 metres (in such a case, you may need to install another re-
mote control system, in order to reduce the length of the cable section).
Thanks to a SIM card, the Sasha remote control system sends,
via short SMS messages, warnings with regards malfunctions to
a specified mobile telephone; the card (not supplied) must be in-
serted to the remote control system during installation.
We advise you check the cover offered by your mobile tele-
phone operator.
With regards the management and configuration of the connection
network (LAN, WLAN, Wi-Fi, etc..), we recommend that you consult
a technical expert in the subject.

Electrical safety

Sasha is a safe appliance, manufactured according to regulations
EN 60335-1, EN 60335-2-105, EN 60335-2-53, EN 61000, EN
55014-1, EN 55014-2 and tested during production to guaran-
tee user safety.
Installation must be carried out by qualified and authorized
personnel, in compliance with the national provisions in force.
It is the installer's responsibility to select the materi-
als, considering the way they will be used; to carry out
the installation correctly; and to verify the condition
of the network to which the system will be connected
and its capability to ensure safety in maintenance
and inspection operations.
Class "1" appliances must be immutably connected, without
intermediate junctions, to the electrical mains and protection
circuit (ground system).
The building's electrical system and ground system
must be efficient and must conform to legal regula-
tions and specific national standards.
Where required, appropriate devices must be provided,
which form part of the fixed system, and installed in
compliance with current legislation in force, with the
purpose of disconnecting the appliance from the mains
(see also "Electrical connections arrangement").
For connection to the electric mains, you will need to in-
stall one or more isolating multi-pole switches, which will
ensure complete disconnection in the instance of a category
III over voltage; these devices must be connected to an area
that complies with the safety regulations governing bath-
room safety.
Switches and electrical devices, according to regulations,
must be connected to areas out of the user's reach.
10