Herunterladen Inhalt Inhalt Diese Seite drucken

Maintenance - MO-EL FIORE Gebrauch Und Wartung

Halogen quarz infrared heater
Inhaltsverzeichnis

Werbung

Verfügbare Sprachen
  • DE

Verfügbare Sprachen

  • DEUTSCH, seite 8
The models for professional use, that are marked with a P in the code, do not have the power cord and the switch. For
professional installation, cabling of the same specification should be selected.
The product is in class I and IP65, wich is the protection rate for the units to be used even outdoor.
For keeping the protection rate of the appliance, the connection of the appliance with the power supply must be done
by means of a minimum IP65 system, as per the standards HD 384 CENELEC for Europe, or international IEC 60346-
7-708 1988.
4. LOCATION
The Fiore range of heaters is deliberately designed to be very flexible in the choice of position. There are three basic op-
tions:
A wall mounting bracket version with a specifically designed fitting for wall attachment (768M). Before drilling
the holes for the dowels, be sure that the wall is solid and that you are far from water tubes or electrical wires. Apply
the drilling template on the wall using adhesive tape and punch in the marked points (see Fig.7). For fixing the appliance
at the wall, drill four holes with a 5 mm diameter bit and fix the wall bracket with the dowels and screws that you find
in the box (Fig.2). Then fix the appliance to the wall bracket using the 2 screws and the 2 half rings (Fig.2). Check that
the arrows on the wall bracket are turned up.
A chain suspended version (768S). Before drilling the holes for the dowels, be sure that the ceiling is solid and that
you are far from water tubes or electrical wires Fix the buttonhole dowels at the ceiling at a distance of about 55 cm.
Fix the 4 half rings a the pipe of the appliance, being sure that the chain is fixed with the screws (Fig.3). The 4 half rings
should be at the opposite sides of the pipe, for the best stability. Ensure that the chains are securely mounted as this
application is designed for overhead use.
A version for mounting on upright (768P). The upright must be from 20 up to 60 mm in diameter. For fixing it, please
see Fig. 4. The upright bracket is studied for holding one appliance or two of them in opposite position.
Before fixing the appliance on the upright, please ensure that it is stable and solid. Preferably, use the
upright that can be ordered as accessory (cod. 002473). The feet must be opened as far as the white
evidenced line on the inferior tube reaches the junction of the feet. Fix the feet to the ground in a proper
way, and then fix the upright to the ground using the chain (Fig. 5).
Ensure that the supply cable is well mounted and that it does not come into contact with the reflector of
the heater or that it does not trail into the heated area. The supply cable can be fixed to the metal pipe
behind the reflector with plastic wrappers.
5. COMMISSIONING
Switch on heater (in the models that have the switch) and confirm that emitter is operating.
Ensure that the heater is aiming its warmth into the target area by adjusting heater angles as necessary by using the
adjustment device on the bracket, after you have loosed the screws of the half rings (Fig. 6). All users should be made
aware of all aspects of operation and safety and these instructions should be retained for reference.
In unoccupied premises it is recommended that the heating system is switched off and isolated from the electrical
supply.

6. MAINTENANCE

Mo-El Fiore heaters contain no moving parts and therefore very little maintenance is required other than to ensure that
there is no excessive build-up of dust/dirt on the reflectors or emitters as this can cause overheating and premature
emitter failure. To clean the appliance, wipe off with a damp cloth.
The accumulation of limestone or incrustations reduces the life and the efficiency of the lamp; it is suggested therefore
to avoid the continued use in presence of water or salt fog. Eventual leavings of salt water will have to be removed
before the use, after having disconnected the appliance, by means of soak in sweet water.
7. EMITTER AND SILICON BUMPERS REPLACEMENT
The emitters used in the Fiore are robust and if knocks and shock vibrations are avoided, they will last for around 5000
hours. When changing the lamp, also the silicon bumpers connected with the lamp must be substituted. They should be
substituted even before if there are signs of aging. Due to the special sealing and anti-shock design of the heater, the emit-
ters are not intended to be user replaceable. Please ensure that all emitters are replaced via the Mo-El service network.
5

Werbung

Inhaltsverzeichnis
loading

Inhaltsverzeichnis