Use And Maintenance; Electrical Installation - MO-EL SHARKLITE Gebrauchsanleitung

EN
1. CAUTION REGARDING THE SECURITY
Instructions should be carefully read before installation and retained by the user. The booklet must be
keeped and delivered to the new user in case of cession of the machine. The Manufacturer reserves the
right to vary the features of the product without prior notice. The technical data are merely indicative.
1. This appliance is intended solely for the use it has been designed for, namely room heating. The Manufacturer is
not responsible for any damage that could happen for improper use.
2. After unpacking make sure that the appliance is complete and shows no signs of visible damage or tampering.
3. Keep packing materials, which are potential dangers, away from children.
4. The appliance is not suited for persons (as well as children) physically, mentally, sensory disabled, or with no
experience, unless they have been supervised or directed by someone responsible of their safety.
5. Do not let the children play with the appliance.
6. Before inserting the plug make sure that the voltage is the same as indicated on the device.
7 . Do not use in presence of gas, inflammable or explosive liquids or substances.
8. Some fundamental rules which apply to all electrical devices must be observed when using the heater:
• Do not touch the heather with wet hands.
• Do not handle with bare feet.
• Do not pull the electric cord or the device itself to unplug it from the socket; pull the plug directly.
• Do not let children play with the electrical appliance.
9. Avoid the use of an extension cord with this product, because the extension cord may overheat and cause a risk
of fire.
10. Do not apply any modification to the product that could compromise the safety.
11. Keep connections dry.
12. If the power supply cord is damaged, avoid to use the appliance. For power cord replacing, please contact the
manufacturer or the technical service or a person with similar qualification, in order to avoid any risk.
13. If the appliance is not used for a long period, disconnect it from the power supply.
14. Always unplug the appliance before doing any maintenance operation.

2. ELECTRICAL INSTALLATION

Installation should always be carried out by a qualified electrician or a competent person in accordance
with the standards HD 384 CENELEC for Europe, or international IEC 60346-7-708 1988, and the standard
AS/NZS 3000 (Australian wiring rules).
The energy supply must be done through a properly grounded socket. In case of directly connection to
supply line a bipolar circuit breaker with contact opening distance of at least 3 mm must be fitted upstream
from the supply line.
Be careful to connect the heater to a supply line protected by 16 A fuses not quick-acting type.
• The heaters should always be installed horizontally only using the mounting brackets provided. This ensures correct
positioning and adequate clearance.
• A minimum air gap of 30 cm should always be allowed between the top of the heater and a ceiling or roof. The ap-
pliance should be 30 cm far from the walls. In case of wall mounting, leave a minimum gap of 8 cm between the
wall and the edge of the heater (fig. 1).
• A safety distance of not less than 100 cm should always be left in front of the SHARKLITE heaters or too near.
• This unit should be mounted at a minimum of 180 cm above ground level (fig. 1). If installed in a toilet, the height
should be 225 cm in zone 1 and zone 2; in zone 3 the minimum above ground level is 180 cm, according with the
rules of each Country.
• Be sure that the heater is not facing the ceiling or inflammable substances.
• The appliance must not be located neither directly below, nor in front of a socket-outlet.
• The heater must be installed so as to prevent that the switches can be touched from those who are in the shower.
• Ensure that there is no possibility of inflammable material, combustible material or curtains coming into contact
with the heater, or lie near the heater.
• Heaters should not be installed in areas where hazardous vapours may be present. Defined in BS5345.
• The heaters are fitted with safety guards. These are intended only to stop large objects from hitting the emitters. On
no account should the heater be operated with the guard removed.
• For consumer use the heaters are fitted with high temperaure rubber flexible cable (H05 RN-F) conforming to BS
6500.
• The models for professional use, that are marked with a "P" in the code, do not have the power cord. For profes-
sional installation, cabling of the same specification should be selected.

USE AND MAINTENANCE

4