Inhaltsverzeichnis
Werbung
Verfügbare Sprachen
Verfügbare Sprachen
EN
1. CAUTION REGARDING THE SECURITY
Instructions should be carefully read before installation and retained by the user. The booklet must be keeped and deliv-
ered to the new user in case of cession of the machine. The Manufacturer reserves the right to vary the features of the
product without prior notice. The technical data are merely indicative.
1.
This appliance is intended solely for the use it has been designed for, namely room heating. The Manufacturer is not
responsible for any damage that could happen for improper use.
2. After unpacking make sure that the appliance is complete and shows no signs of visible damage or tampering.
3. Keep packing materials, which are potential dangers, away from children.
4. The appliance is not suited for persons (as well as children) physically, mentally, sensory disabled, or with no experi-
ence, unless they have been supervised or directed by someone responsible of their safety.
5. Do not let the children play with the appliance.
6. Before inserting the plug make sure that the voltage is the same as indicated on the device.
7 .
Do not use in presence of gas, inflammable or explosive liquids or substances.
8. Some fundamental rules which apply to all electrical devices must be observed when using the heater:
• Do not touch the heather with wet hands.
• Do not handle with bare feet.
• Do not pull the electric cord or the device itself to unplug it from the socket; pull the plug directly.
• Do not let children play with the electrical appliance.
9. Avoid improper use of extension cords.
10. Do not apply any modification to the product that could compromise the safety.
11. Keep connections dry.
12. If the appliance is not used for a long period, disconnect it from the power supply.
13. Always disconnect the appliance before doing any maintenance operation.
2. CAUTION REGARDING THE INSTALLATION OF THE APPLIANCE
Installation should always be carried out by a qualified electrician or a competent person in accordance with the standards
HD 384 CENELEC for Europe, or international IEC 60346-7-708 1988, and the standard AS/NZS 3000 (Australian wiring
rules). The energy supply must be done through a properly grounded socket. The appliance must be connected to the
power supply by a H05RN-F cable, gotten properly into dimension in respect to its own length and the kind of the con-
nection (see the Table 1)
Model
791
220-240V ~
Power supply
50–60Hz
Total power
2000 W
Current
Cable H05RN-F
3x1,5 mm²
(min.section)
(*) Cable minimum section - per 5 m length.
A omni-polar circuit breaker with contact opening distance of at least 3 mm must
be fitted upstream from the supply line.
Be careful to connect the heater to a supply line protected by 16A fuses not quick-
acting type.
Wall mounting using the braket (provided)
• Make sure that the wall where you plan to mount the appliance is solid, and free of electrical cables or water pipes
inside.
• Fasten the bracket to the wall by means of 2 dowels at least, passing through the A holes (fig.1).
• Use the B holes just as reference (fig.1).
• This heater is intended for permanent installation.
• The heater can be angled on its bracket in correspondence to the C screw, and the modules can be pointed in corre-
spondence to the D couplings (fig.2 ). When the adjustment has been made, tighten all the screws.
• Be sure that the heater is not facing the ceiling or inflammable substances.
USE AND MAINTENANCE
792
220-240V ~
50–60Hz
4000 W
9 A
18 A
3x2,5 mm²
793
794
380-415V ~
220-240V ~
50–60Hz
50–60Hz
3P+N
3x2000 W
1500 W
3 x 9 A
7 A
5x1,5 mm²
3x1,5 mm²
4
795
796
380-415V ~
220-240V ~
50–60Hz
50–60Hz
3P+N
3000 W
3x1500 W
14 A
3 x 7 A
3x2,5 mm²
5x1,5 mm²
TABLE 1
Werbung
Inhaltsverzeichnis
