Product Safety Information; Product Specifications; Mounting Instructions - Ingersoll-Rand QA4AAL-011 Technische Produktdaten

Product Safety Information

Intended Use:
These Air Angle Wrenches and Nut Runners are designed for assembly applications requiring precise torque control, accuracy, consistency, and
repeatability.
• Failure to observe the following warnings, and to avoid these potentially hazardous situations, could result in death or serious
injury.
• Always turn off the air supply, bleed the air pressure and disconnect the air supply hose when not in use, before installing, removing
or adjusting any accessory on this tool, or before performing any maintenance on this tool or any accessory.
•
If the clutch is adjusted over the maximum power output of the tool, the clutch will not function and the tool will stall.
• If the tool is operated below the recommended air pressure, the clutch at the higher torque settings may not function properly
causing the tool to stall.
• If a tool stalls the full torque capacity of the tool will be applied to the operator's hands, unless a suspension arm or reaction bar is
used. This force may cause serious personal injury from crushing, pinching, loss of balance or loss of control of the tool.
• Use clutch adjustment screwdriver supplied with the tool.
• Straight tool configurations must be mounted using proper flanges as specified in Parts Information Manual 80160344.
For additional information refer to Product Safety Information Manual Form 04585006.
Manuals can be downloaded from ingersollrandproducts.com

Product Specifications

Information given for tool operation at 90psi / 6.2bar
Model(s) Free Speed
rpm
QA4AAL-011 1025
QA4AAL-015 800
QA4AAL-020 625
QA4AAL-030 425
QA4AAL-040 325
QA4AAL-055 200
QA4ASL-012 1050
QA4ASL-015 850
QA4ASL-020 600
QA4ASL-027 450
QA4ASL-046 250
† K = 3dB measurement uncertainty
pA
Sound and vibration values were measured in compliance with internationally recognized test standards. The exposure to the user in
a specific tool application may vary from these results. Therefore, on site measurements should be used to determine the hazard level
in that specific application.
Operating range of air pressure for this tool is 76 - 90 PSI (5.3 - 6.2 bar). Clutch will function properly within this range. Outside this range, the
tool may experience symptoms as described in the warnings given above in the Product Safety Information Section of this manual.
Note: Remote tool performance is approximately 8% lower than equivalent lever tool.

Mounting Instructions

All in-line/straight tool configurations must be mounted using appropriate flange as specified in Parts Information Manual 80160344. A
mounting flange is available for all angle tool configurations. Refer to Parts Information Manual 80160344 for specific mounting information.
80160336_ed6
Clutch Torque Range Stall Torque
Nm
5 - 11.5
7 - 15
9 - 20
15 - 30
20 - 40
25 - 55
6 - 12
7 - 15
9 - 20
14 - 27
20 - 46
All information given for operation at 90 psi / 6.2 bar for all models
Sound Level dB(A)
(ISO15744)
† Pressure (L )
p
79.3
WARNING
Information given for tool operation at 76 psi / 5.3 bar
Free Speed
Nm rpm
13 953
16 744
21 581
31 395
41 302
58 186
13 977
16 791
21 558
28 419
47 233
WARNING
Clutch Torque Range Stall Torque
Nm
5 - 9.7
7 - 12.7
9 - 17
15 - 25.5
20 - 34
25 - 45.5
6 - 10
7 - 12.7
9 - 17
14 - 22.7
20 - 38
Vibration Level (m/s
(ISO28927)
< 2.5
EN
Nm
11.1
13.6
17.9
26.4
34.9
48.1
11.7
13.6
17.9
23.8
39.0
)
2
EN-1