Inhaltsverzeichnis
Werbung
Verfügbare Sprachen
Verfügbare Sprachen
Product Safety Information
Intended Use: These Cordless Impact Wrenches are designed to remove and install threaded fasteners.
⚠
WARNING: Read all safety warnings, instructions, illustrations, and specifications provided with this power tool. Failure to follow the
warnings and instructions may result in electric shock, fire and/or serious injury. Save all warnings and instructions for future reference.
● Responsibly recycle or dispose of Batteries. Do not puncture or burn batteries. Improper disposal may endanger the environment or cause
personal injury.
● Only use Tools with appropriate voltage Ingersoll Rand batteries and Charger. Use of any other batteries may create a risk of fire, personal
injury or property damage.
Ingersoll Rand has updated their battery labeling from fully charged voltage to nominal voltage to follow current guidelines. The new labeling will
reflect the nominal voltage of the batteries adjusting from 12V to 10.8V, from 20V to 18V, and from 40V to 36V.
Nominal voltage is the average voltage presented while the battery is in use. Note the battery performance has not be impacted due to this guideline
adherence and the batteries maintain compatibility within their respective voltage platforms, for example an IQV® 20 series tool corresponds with an
IQV® 20 series battery.
For additional information, refer to Cordless Impact Wrench Safety Manual Form 04581146, Battery Charger Safety Information Manual
Form 10567832 and Battery Safety Information Manual Form 10567840.
Manuals can be downloaded from ingersollrand.com
Power Control System
The power control system on this tool can be adjusted using the power regulator. To select the power mode, pull and release the trigger to turn on
the tool and illuminate the power mode LEDs. Press the button on the tool foot to cycle through the three power modes.
Modes 1 and 2 provide power control in both forward and reverse directions. Mode 3 provides maximum power in both forward and reverse
directions.
Mode
Direction
1
2
3
Impact wrenches are not torque wrenches. Connections requiring specific torque must be checked with a torque meter after fitting with an
impact wrench. Improperly torqued fasteners may loosen and cause injury.
Product Specifications
Model
W3111
W3131
W3151
Model
W3111
W3131
W3151
† K
= 3dB measurement uncertainty
pA
‡ K
= 3dB measurement uncertainty
wA
* K = Vibration measurement uncertainty
TL-W3001-PIM_ed2
No-Load Speed
Name
rpm
Low Power
0-725
Mid Power
0-1,600
Max. Power
0-2,800
Voltage
Drive
V, DC
Type
Quick Change Hex
20
Square
Sound Level dB(A)
(EN 62841)
†Pressure (L
)
p
90
WARNING
Impacts per
Max. Forward
Minute
Torque
bpm
ft-lb (Nm)
70 (W3111)
0-1,400
90 (W3131)
100 (W3151)
140 (W3111)
0-3,000
150 (W3131)
180 (W3151)
265 (W3111)
0-4,200
300 (W3131)
320 (W3151)
WARNING
Impacts per Minute
Size
bpm
1/4"
3/8"
4,200
1/2"
‡Power (L
)
w
101
Conforms to UL STD. 62841-1 & 62841-2-2.
Certified to CSA STD. C22.2 No. 62841-1 & 62841-2-2.
Description
Torque-limiting, continuous run
Torque-limiting, continuous run
Maximum torque, continuous run
No-Load Speed
Max. Reverse Torque
rpm
ft-lb (Nm)
2,800
Battery Model - BL2022, BL2023
Vibration (m/s
)
2
(EN 62841)
Level
18.1
EN
265
300
320
*K
5.8
4000415
EN-1
Werbung
Inhaltsverzeichnis
