Specifications - Lincoln Electric MIG 216 Betriebsanleitung

INSTRUCTION MANUAL FOR WIRE WELDING MACHINE
IMPORTANT
READ THIS MANUAL AND THE SAFETY RULES
MANUAL CAREFULLY BEFORE INSTALLING, USING,
OR SERVICING THE WELDING MACHINE, PAYING
SPECIAL ATTENTION TO SAFETY RULES. CONTACT
YOUR DISTRIBUTOR
UNDERSTAND THESE INSTRUCTIONS.
This machine must be used for welding only. It must not be
used to defrost pipes.
It is also essential to pay special attention to the "SAFETY
RULES" Manual. The symbols next to certain paragraphs
indicate points requiring extra attention, practical advice or
simple information.
This MANUAL and the "SAFETY RULES" MANUAL must
be stored carefully in a pica familiar to everyone involved in
using the machine. They must be consulted whenever
doubts arise and be kept for the entire lifespan of the
machine; they will also be used for ordering replacement
parts.
1 PLACEMENT
Unpack the machine and place it in an adequately
ventilated area, dust-free if possible, taking care not to
block the air intake and outlet from the cooling slots.
CAUTION: REDUCED
overheating and could damage internal parts.
Keep at least 500 mm of free space around the machine.
Never place any filtering device over the air intake points of
this welding machine.
The warranty shall become void if any type of filtering
device is used.
2 DESCRIPTION OF THE MACHINE (pict. 1)
A) Welding torch.
B) Thickness setting knob.
Adjusts welding parameters according to the thickness
of materials to be welded.
C) LED - thermostat.
Lights only when the thermostat is tripped and
interrupts the machine operation.
D) LED - pilot light.
Lights when the welding power source is plugged to
power supply and the switch (I) is in ON position.
E) Arc setting knob.
Adjusts the welding arc length according to the
quantity of filler material to be deposited and to the
type of welding bead to be realized.
F) Wire diameter setting knob.
Selects the appropriate synergic curve according to
the diameter and the type of wire to be welded.
G) Earth cable output.
H) Gas hose fitting.
I) Bipolar light switch.
J) Power supply cable output.
3 GENERAL DESCRIPTIONS

3.1 SPECIFICATIONS

This welding machine allows welding of mild steel.
IF YOU DO NOT FULLY
AIR CIRCULATION causes
3.2 EXPLANATION OF TECHNICAL SPECIFICATIONS
IEC60974-1 The welding machine is manufactured
IEC60974-10 according
standards.
Cl. A Machine for professional and industrial use.
Single-phase transformer - rectifier
Flat characteristic.
Suitable for continuous electrode welding.
I max Unconventional welding current.
2
This value represents the max. limit
attainable in welding.
U0 Secondary open-circuit voltage.
X Duty cycle percentage.
The duty cycle expresses the percentage
of 10 minutes during which the welding
machine may run at a certain current
without overheating.
I Welding current
2
U Secondary voltage with welding current
2
I .
2
U Rated supply voltage
1
1~ 50/60Hz 50- or 60-Hz single-phase power supply.
I max Maximum absorbed current value.
1
I eff This is the maximum value of the actual
1
current absorbed, considering the duty
cycle.
IP23 Protection rating for the housing.
Grade 3 as the second digit means that this
equipment is suitable for use outdoors in
the rain.
Suitable for use in high-risk environments.
NOTES: The welding machine has also been designed for
use in environments with a pollution rating of 3. (See IEC
60664)
3.3 DESCRIPTION OF PROTECTION
This device is protected by a thermostat that normally is
closed and that is placed on output diodes.
When the thermostat is tripped the machine stops welding,
while the motor-driven fan continues to run and the LED C
lights.
6
pict. 2
to these international