Makita DHS782 Betriebsanleitung Seite 16

Sighting
For straight cuts, align the 0° position on the front of the
EDVH ZLWK \RXU FXWWLQJ OLQH )RU ƒ EHYHO FXWV DOLJQ WKH
45° position with it.
Fig.15: 1. &XWWLQJ OLQH ƒ SRVLWLRQ 2. Cutting line
ƒ SRVLWLRQ
Lighting the lamp
CAUTION:
Do not look in the light or see the
source of light directly.
To turn on the lamp without running the tool, pull the
switch trigger without pressing the lock-off button.
To turn on the lamp with the tool running, press and hold
the lock-off button and pull the switch trigger.
The lamp goes out 10 seconds after releasing the switch trigger.
Fig.16: 1. Lamp
NOTE: 8VH D GU\ FORWK WR ZLSH WKH GLUW RII WKH OHQV RI
the lamp. Be careful not to scratch the lens of lamp, or
LW PD\ ORZHU WKH LOOXPLQDWLRQ
Hook
Optional accessory
CAUTION:
Always remove the battery when
hanging the tool with the hook.
CAUTION:
Never hook the tool at high loca-
tions or on the surfaces where the tool may lose
the balance and fall.
CAUTION:
Do not pull the tool downward
when it is hooked.
7KH KRRN LV FRQYHQLHQW IRU KDQJLQJ WKH WRRO WHPSRUDULO\
Fig.17
Attach the hook with the screws as illustrated.
Fig.18: 1. Hook 2. Screw
7R XVH WKH KRRN VLPSO\ WXUQ WKH KRRN XQWLO LW VQDSV LQWR
the open position.
:KHQ QRW LQ XVH DOZD\V WXUQ WKH KRRN XQWLO LW VQDSV LQWR
the closed position.
Fig.19: 1. Open position 2. Closed position
Electric brake
This tool is equipped with an electric blade brake. If the tool con-
VLVWHQWO\ IDLOV WR TXLFNO\ VWRS WKH FLUFXODU VDZ EODGH DIWHU VZLWFK
lever release, have tool serviced at a Makita service center.
CAUTION:
The blade brake system is not a
substitute for blade guard. NEVER USE TOOL
WITHOUT A FUNCTIONING BLADE GUARD.
SERIOUS PERSONAL INJURY CAN RESULT.
Electronic function
7KH WRROV HTXLSSHG ZLWK HOHFWURQLF IXQFWLRQ DUH HDV\ WR
RSHUDWH EHFDXVH RI WKH IROORZLQJ IHDWXUH V 
Soft start feature
Soft start because of suppressed starting shock.
ASSEMBLY
CAUTION:
Always be sure that the tool is
switched off and the battery cartridge is removed
before carrying out any work on the tool.
Hex wrench storage
:KHQ QRW LQ XVH VWRUH WKH KH[ ZUHQFK DV VKRZQ LQ WKH
¿JXUH WR NHHS LW IURP EHLQJ ORVW
Fig.20: 1. Hex wrench
Removing or installing circular saw
blade
CAUTION:
Be sure the circular saw blade is
installed with teeth pointing up at the front of the
tool.
CAUTION:
Use only the Makita wrench to
install or remove the circular saw blade.
To remove the circular saw blade, press the shaft lock
IXOO\ VR WKDW WKH FLUFXODU VDZ EODGH FDQQRW UHYROYH DQG
use the hex wrench to loosen the hex bolt. Then remove
WKH KH[ EROW RXWHU ÀDQJH FLUFXODU VDZ EODGH DQG ULQJ
FRXQWU\ VSHFL¿F 
Fig.21: 1. Shaft lock 2. Hex wrench 3. Loosen
4. Tighten
For tool without the ring
Fig.22: 1. Hex bolt 2. 2XWHU ÀDQJH 3. Circular saw
blade 4. ,QQHU ÀDQJH
For tool with the ring
Fig.23: 1. Hex bolt 2. 2XWHU ÀDQJH 3. Circular saw
blade 4. Ring 5. ,QQHU ÀDQJH
To install the circular saw blade, follow the removal
procedure in reverse.
)RU WRRO ZLWK WKH LQQHU ÀDQJH IRU
other than 15.88 mm hole-diameter
saw blade
7KH LQQHU ÀDQJH KDV D FHUWDLQ GLDPHWHU SURWUXVLRQ RQ
one side of it and a different diameter protrusion on the
other side. Choose a correct side on which protrusion
¿WV LQWR WKH VDZ EODGH KROH SHUIHFWO\ 0RXQW WKH LQQHU
ÀDQJH RQWR WKH PRXQWLQJ VKDIW VR WKDW WKH FRUUHFW VLGH
RI SURWUXVLRQ RQ WKH LQQHU ÀDQJH IDFHV RXWZDUG DQG WKHQ
SODFH VDZ EODGH DQG RXWHU ÀDQJH
Fig.24: 1. Mounting shaft 2. ,QQHU ÀDQJH 3. Circular
saw blade 4. 2XWHU ÀDQJH 5. Hex bolt
WARNING:
BE SURE TO TIGHTEN THE HEX
BOLT CLOCKWISE SECURELY. Also be careful
not to tighten the bolt forcibly. Slipping your hand
from the hex wrench can cause a personal injury.
WARNING:
Make sure that the protrusion "a"
RQ WKH LQQHU ÀDQJH WKDW LV SRVLWLRQHG RXWVLGH ¿WV
into the saw blade hole "a" perfectly. Mounting the
blade on the wrong side can result in the dangerous
vibration.
16 ENGLISH