General Warnings - AERMEC FCX A Serie Bedienungs- Und Installationsanleitung

FCX A
13.

GENERAL WARNINGS

The FCX AERMEC units are con-
structed according to the recog-
nised technical standards and
safety regulations. They have
been designed and must be used
for air conditioning and heating
purposes, in accordance with
their technical features.
Any contractual or extra-contrac-
tual liability of the Company is
excluded for injury/damage to
persons, animals or objects owing
to installation, regulation and
maintenance errors or improper
use. All uses not expressly indicat-
ed in this manual are prohibited.
Use suitable Personal Protective
Equipment (PPE) during installa-
tion, maintenance, and cleaning
stages.
Do not use the unit as storage for
equipment or spare parts. Any
use other than that indicated in
this manual is prohibited as it can
generate dangerous situations.
ATTENTION: the electric and
hydraulic connections, together
with installation of the fan coils
and their accessories must only
be performed by technicians
who have the technical-profes-
sional requisites for installation,
transformation, extension and
maintenance of the systems and
who can verify these functions in
terms of safety and functionality
(in accordance with the national
laws in force in the country of
installation). In this manual they
will be also identified as: expe-
rienced and qualified technician
with specific technical knowledge.
AERMEC will not be liable for
damage due to failure to follow
these instructions.
Make sure the unit has not been
damaged during transport before
installation.
• using a damaged machine could
be dangerous.
• the support surface must with-
stand the weight of the unit.
IFCXALJ 1011 - 6456043_06
Note:
Always indicate the serial num-
ber for future reference and for
any communication with AER-
MEC S.p.A.
STORING THE DOCUMENTATION
Hand over the instructions with
all the related documentation to
the system user, who must store
the instructions so that they are
always available in case of neces-
sity.
WARNINGS REGARDING SAFETY
AND INSTALLATION STANDARDS
Follow the indications below to
install the equipment correctly.
The completion of all operations,
according to specific require-
ments, is left to the experience of
the installer.
Do not modify or tamper with the
units, as dangerous situations can
occur. The manufacturer will not
be liable for any damage caused.
The validity of the warranty shall
be void in the event of failure to
comply with the indications men-
tioned in this manual.
Before starting any operations,
READ THESE INSTRUCTIONS
CAREFULLY AND CARRY OUT THE
SAFETY CHECKS TO AVOID ALL
RISKS.
All the staff involved must have
thorough knowledge of the oper-
ations and any danger that may
arise when the installation opera-
tions are carried out.
The unit must be installed to facil-
itate routine (filter cleaning) and
special maintenance operations.
ATTENTION: the fan coil is con-
nected to the power supply and
the hydraulic circuit. Operations
performed by persons who do not
have the required technical skills
can lead to personal injury to the
operator or damage the unit and
the surrounding environment.
ATTENTION: The unit must
be installed in compliance with
national regulations.
ATTENTION: make sure that
the power supply has been dis-
connected before carrying out
any interventions.
ATTENTION: Install a device,
master switch or electric plug that
allows the unit's power supply to
be completely disconnected.
ATTENTION: In order to pro-
tect the unit against short circuits,
mount a magnet circuit breaker
omnipolar switch on the power
supply line. In order to avoid
any danger due to the accidental
rearming of the thermal cut-out
device, this appliance must not be
powered with an external switch-
ing device, such as a timer, or be
connected to a circuit that is regu-
larly powered or disconnected
from the service.
ATTENTION! DANGER! Any use
other than what is indicated by
Aermec is prohibited.
SUPPLY THE FAN COIL ONLY
WITH THE VOLTAGE VALUE IN-
DICATED IN THE DATA PLATE
The fan coil may be permanently
damaged if a different electric
power supply is used.
EN
19