Removing The Child Car Seat; Folding And Transport Of The Seat; Installing And Removing The Side Safety System; Installing The Safe Pad - Chicco FOLD&GO I-SIZE Gebrauchsanleitung

seat backrest (Fig. 5A-5B).
WARNING! Never pass the car safety belt in
positions other than those indicated in this in-
struction booklet! (fig. 16).
WARNING! Make sure that your child is cor-
rectly secured in the child car seat, so that he
does not slide forward.
WARNING! Check that the unused Isofix rigid
connectors are not pulled out.
WARNING! When the child car seat is not in
use, it should always be left secured with the
3-point belt to the car seat or stowed in the
boot. In fact, an unsecured car seat may pose
a hazard to the passengers in case of accident
or sudden braking.
To remove the child from the child car seat,
simply unfasten the buckle of the car safety
belt, accompanying the belt during rolling.

3. REMOVING THE CHILD CAR SEAT

WARNING! Remove the child from the child
car seat before removing.
1. Release the car seat belt.
2. Remove the diagonal part of the belt from
the guide, accompanying it during rolling.
3. If the child car seat has also been fastened
with the Isofix rigid connectors, it is neces-
sary to release them from the appropriate
hooks using the release button (Q).
WARNING! The release button (Q) may not be
accessible, so you need to press and hold the
Isofix (P) connector eject button and simulta-
neously pull the child car seat towards you until
the Isofix connectors are fully pulled out.
• Pull the two red buttons (Q) to release the
connectors from the corresponding Isofix
connections of the car seat (Fig.18), so that
the indicator is totally red.
• Push the rigid connectors into the base of the
child car seat and completely retract them
into the base, holding down one of the but-
tons (P) (Fig. 19).

4. FOLDING AND TRANSPORT OF THE SEAT

For easy transport of the child car seat, it is pos-
sible to compact it by folding the backrest over
the seat. To carry out this step, it is necessary to
check that the backrest is in the lowest position
(see paragraph "7.1 ADJUSTING THE BACKREST
HEIGHT").
At this point, use the backrest release lever (M)
to fold the backrest into the seat (Fig. 20).
WARNING! With the backrest not fully low-
ered, the backrest release lever (M) may not be
easily accessible.
To keep the child car seat compact, remove
the backrest blocking strip (J) from its seat and
fasten it to one of the two special slots on the
side of the backrest width adjustment wheel
(K) (Fig. 21).
To comfortably move the seat in this configura-
tion, you can use the carrying handle (O) locat-
ed on the back of the seat (Fig. 22 ).
5. INSTALLING AND REMOVING THE SIDE
SAFETY SYSTEM
The Side Safety System (T) is a device that is in-
stalled on the door side for utmost protection in
the case of a side impact.
To install it, insert the hook "1" in the hole on
the side flap (D) on the door side and press the
central part until the other end "2" is also fas-
tened to the structure (Fig. 23).

6. INSTALLING THE SAFE PAD

The Safe Pad (H) is a device that must ALWAYS
be installed on the diagonal vehicle seat belt
to ensure proper protection in the event of an
impact.
For correct installation, it is necessary to po-
sition the diagonal belt under the two Velcro
straps of the Safe Pad (Fig. 24) and close it on
itself making sure that the circular part is posi-
tioned between the chin and the chest of the
child (Fig. 25).
WARNING! The Safe Pad must ALWAYS be
used.

7. OTHER OPERATIONS

7.1 ADJUSTING THE BACKREST HEIGHT

It is possible to adjust the backrest height in
9 positions to the height of your child. Ensure
that the child's head is secured and that the
car's diagonal belt is correctly supported on
the child's shoulder. When adjusting the height
of the backrest, check that the diagonal belt
guide (B) is positioned above the shoulder at a
maximum distance of 2 cm (Fig. 26).
21