Chicco FOLD&GO I-SIZE Gebrauchsanleitung Seite 20

WARNING! Make sure that the seat has been
fitted correctly by checking that the two indi-
cators (S) are green (Fig. 9).
3. Push the child car seat firmly against the
backrest of the car seat with the button
pressed (p) to make sure that it adheres per-
fectly to the car seat (Fig. 10).
WARNING! The back of the child car seat must
closely adhere to the car seat.
4. Place the child in the seat with their back
leaning against the backrest. Check the
height of the backrest (see section "7.1 AD-
JUSTING THE BACKREST HEIGHT"). Check
the width of the backrest (see section "7.2
ADJUSTING THE WIDTH OF THE BACKREST").
5. Insert the diagonal portion of the car seat
belt in the diagonal belt guide (B) (Fig. 11).
6. Fasten the vehicle seat belt by passing the
waist part through the seat Belt Positioner
(G) (Fig. 12).
7. Pull the diagonal part of the belt upwards
so the entire belt is taut and fits closely over
the child's legs and chest (without being too
tight) (Fig. 13).
WARNING! Check that the vehicle safety belt is
tightened properly.
WARNING! Check that the vehicle safety belt is
free of knots (Fig. 14).
WARNING! Check that the diagonal seat belt
fits correctly across your child's shoulders (Fig.
15) and does not press on the their neck; if
necessary, adjust the height of the backrest
(see section "7.1 ADJUSTING THE BACKREST
HEIGHT").
WARNING! Check that the car seat belt ad-
juster is reclined or at least aligned with the car
seat backrest (Fig. 5A-5B).
WARNING! Never pass the vehicle seat belt
in positions other than those indicated in this
instruction booklet! (Fig. 16)
WARNING! When the child car seat is not in
use, it should always be left secured with the
Isofix connectors to the car seat or stowed in
the boot. In fact, an unsecured Car seat may
pose a hazard to the passengers in case of acci-
dent or sudden braking.
To remove the child from the child car seat,
simply unfasten the buckle of the car safety
belt, accompanying the belt during rolling.
2.2 INSTALLING THE CHILD CAR SEAT WITH
THE VEHICLE SEAT BELT
WARNING!The text and figures of these in-
structions are for the installation of the child
car seat on the correct back seat. When fitting
the child car seat in other position these oper-
ations should in any case be carried out in the
same order.
WARNING! The seat MUST ALWAYS be in-
stalled with the vehicle seat belt.
WARNING! •Check that the car seat headrest
does not interfere with the headrest of the
child car seat: it must not push it forward (Fig.
6). If this happens, remove the headrest from
the car seat. Remember to reposition the head-
rest on the vehicle seat if the child car seat is
removed and the seat is used by a passenger.
1. Position the child car seat NOT reclined and
with the connectors NOT pulled out against
the backrest of the car seat (Fig. 17).
WARNING! The back of the child car seat must
closely adhere to the car seat.
2. Place the child in the seat with their back
leaning against the backrest. Check the
height of the backrest (see section "7.1 AD-
JUSTING THE BACKREST HEIGHT"). Check
the width of the backrest (see section "7.2
ADJUSTING THE WIDTH OF THE BACKREST").
3. Insert the diagonal portion of the car seat
belt in the diagonal belt guide (B) (Fig. 11).
4. Fasten the vehicle seat belt by passing the
waist part through the Belt Positioner (G)
(Fig. 12).
5. Pull the diagonal part of the belt upwards
so the entire belt is taut and fits closely over
the child's legs and chest (without being too
tight) (Fig. 13).
WARNING! Check that the vehicle safety belt is
tightened properly.
WARNING! Check that the vehicle safety belt is
free of knots (Fig. 14).
WARNING! Check that the diagonal seat belt
fits correctly across your child's shoulders (Fig.
15) and does not press on the their neck; if
necessary, adjust the height of the backrest
(see section "7.1 ADJUSTING THE BACKREST
HEIGHT").
WARNING! Check that the car seat belt ad-
juster is reclined or at least aligned with the car
20