For The Customers In Europe - Sony HVO-1000MD Handbuch

Recommended separation distances between portable and mobile RF communications equipment and the
The HVO-1000MD is intended for use in an electromagnetic environment in which radiated RF disturbances are controlled.
The customer or the user of the HVO-1000MD can help prevent electromagnetic interference by maintaining a minimum
distance between portable and mobile RF communications equipment (Transmitters) and the HVO-1000MD as
recommended below, according to the maximum output power of the communications equipment.
Rated maximum output power of transmitter
W
0.01
0.1
1
10
100
For transmitters rated a maximum output power not listed above, the recommended separation distance d in meters (m) can
be estimated using the equation applicable to the frequency of the transmitter, where P is the maximum output power rating
of the transmitter in watts (W) according to the transmitter manufacturer.
NOTE 1: At 80 MHz and 800 MHz, the separation distance for the higher frequency range applies.
NOTE 2: These guidelines may not apply in all situations. Electromagnetic propagation is affected by absorption and
reflection from structures, objects and people.
Caution
When you dispose of the unit or accessories, you must
obey the laws in the relative area or country and the
regulations in the relative hospital.
WARNING on power connection
Use a proper power cord for your local power supply.
1. Use the approved Power Cord (3-core mains lead) /
Appliance Connector / Plug with earthing-contacts that
conforms to the safety regulations of each country if
applicable.
2. Use the Power Cord (3-core mains lead) / Appliance
Connector / Plug conforming to the proper ratings
(Voltage, Ampere). If you have questions on the use of
the above Power Cord / Appliance Connector / Plug,
please consult a qualified service personnel.
Warning on power connection for medical
use
Please use the following power supply cord.
With connectors (plug or female) and cord types other than
those indicated in this table, use the power supply cord that
is approved for use in your area.
United States and Canada
Plug Type HOSPITAL GRADE*
Cord Type Min.Type SJT
Min.18 AWG
Minimum Rating for Plug 10A/125V
and Appliance Couplers
Safety Approval UL Listed and CSA
*Note: Grounding reliability can only be achieved when the equipment is
connected to an equivalent receptacle marked 'Hospital Only' or 'Hospi-
tal Grade'.
HVO-1000MD
Separation distance according to frequency of transmitter
150 kHz to 80 MHz 80 MHz to 800 MHz
d = 1.2 √P
0.12
0.38
1.2
3.8
12
On cleaning
When the cabinet becomes dirty
Before cleaning the unit, be sure to power the unit off and
disconnect the power plug.
If the body of the unit is dirty, clean it with a soft, dry cloth.
In extreme cases, use a cloth steeped in a little neutral
detergent, then wipe dry. Do not use organic solvents such
as alcohol or thinners, as these may cause discoloration or
other damage to the finish of the unit.
For the customers in Canada
This unit has been certified according to Standard CSA
C22.2 No.601.1.

For the customers in Europe

The manufacturer of this product is Sony Corporation,
1-7-1 Konan, Minato-ku, Tokyo, Japan.
The Authorized Representative for EMC, medical devices,
and product safety is Sony Deutschland GmbH,
Hedelfinger Strasse 61, 70327 Stuttgart, Germany;
TEL: (0)711 5858 0; FAX: (0)711 5858 235.
For any service or guarantee matters please refer to the
addresses given in separate service or guarantee
documents.
CAUTION
• For safety, do not connect the connector for peripheral
device wiring that might have excessive voltage to this
port. Follow the instructions for this port.
• When you connect the LAN cable of the unit to
peripheral device, use a shielded-type cable to prevent
malfunction due to radiation noise.
m
800 MHz to 2.5 GHz
d = 1.2 √P d = 2.3 √P
0.12
0.38
1.2
3.8
12
0.23
0.73
2.3
7.3
23
15