Hot Water - Saeco Mini bar Bedienungsanleitung

Programming is complete. From now on the machine will
brew:
•• The same quantity as the one previously selected by
pressing and releasing the button (15).
•• Twice the quantity as the one previously selected by
pressing and releasing the button (16).
6 TIPS FOR CHOOSING COFFEE
As a general rule any type of coffee available on the
market can be used. However, coffee is a natural product
and its  avour changes according to its origin and blend;
it is therefore a good idea to try different types of coffee
in order to  nd the most suited to your personal taste.
For best results, we recommend using blends which are
expressly indicated for espresso coffee machines. Coffee
should always be dispensed by the pressurized porta lter
without dripping.
The speed of coffee dispensing can be modi ed by
slightly changing the amount of coffee in the  lter and/or
by using a different coffee grind.
Saeco recommends using single-dose coffee pods
marked ESE for a tasty coffee and easier cleaning and
preparing.
BEFORE USING THE HOT WATER/STEAM JET,
MAKE SURE THAT THE CAPPUCCINATORE IS
POSITIONED OVER THE DRIP TRAY.
7

HOT WATER

Danger of scalding! When brewing starts, spurts
of hot water may come out. The spout can reach
high temperatures: do not touch it with bare hands.
•• (Fig.3) - Press the ON/OFF button (2).
•• Wait for the buttons (15 - 16) to be permanently on.
•• (Fig.18) - Place a container or a teacup under the
cappuccinatore.
•• (Fig.5) –– Open the knob (4).
•• (Fig.6) - Press the button (17)
•• When the required amount of hot water has been
dispensed, press the button (17) again.
•• (Fig.5) - Close the knob (4).
•• Remove the container with hot water.
By pressing the buttons (15) or (16), the machine
will brew the same quantity of hot water as the
one programmed in Section 5.2.
8 STEAM / CAPPUCCINO
Danger of scalding! When brewing begins, spurts
of hot water may come out. The spout can reach
high temperatures: do not touch it with bare hands.
•• (Fig.3) - Press the ON/OFF button (2).
•• Wait for the buttons (15 - 16) to be permanently on.
•• (Fig.19) - Press the button (18).
•• Wait for the button (18) to be permanently on. The machine
is now ready for steam ejection.
•• (Fig.18) - Place a container under the cappuccinatore.
•• (Fig.5) - Open the knob (4) for a few seconds, so that
remaining water  ows out of the cappuccinatore. In a
short time only steam will come out.
A maximum steam ejection of 60 seconds is
recommended.
•• Close the knob (4) and remove the container.
•• Fill 1/3 of the container you wish to use to prepare the
cappuccino with cold milk.
Use cold milk to get a better result.
•• (Fig.20) - Immerse the cappuccinatore suction pipe in the
milk container.
•• (Fig.5) - Open the knob (4) by turning it anticlockwise.
•• (Fig.21) - Adjust the froth quantity by using the pin. Lift it
gently to get a greater quantity of froth.
•• When brewing ends, close the knob (4) and remove the
cup with the frothed milk.
After preparing the cappuccino, immerse the suction
pipe into a container with fresh clean water and eject
steam. The cappuccinatore is clean when clean water is
dispensed. Clean the suction pipe externally with a damp
cloth.
The cappuccinatore must be removed and
completely washed once a week.
•• (Fig.19) - Press the button (18) again.
•• Prime the circuit as described in section 4.5 to make the
machine ready for use.
Note: the machine is ready when the buttons (15
and16) are permanently on.
Note: if it is not possible to dispense a
cappuccino as described, prime the circuit as
explained in Section 4.5, then repeat the procedure.
The same procedure can be used to heat other
beverages.
•• After this operation, clean the steam spout with a damp
cloth.
•• 21 ••