Saeco Mini bar Bedienungsanleitung Seite 22

9 PANNARELLO
Pannarello can be used for dispensing hot water and
ejecting steam instead of the cappuccinatore.
Remove the cappuccinatore before installing the
Pannarello (Fig.29-30):
- Loosen the ring nut without taking it off.
- Remove the cappuccinatore coupling from the steam
spout.
Install the Pannarello (Fig.31):
- Insert the Pannarello completely into the steam spout.
- Tighten the ring nut securely.
(Fig.32 - Fig.33) - Prepare the machine by using the
Pannarello as described in Sections 7 and 8 to dispense
hot water or steam.
(Fig.34 - Fig.35) - After using the machine, when it has
cooled down, remove the lower part of the Pannarello
and wash it with lukewarm water.
(Fig.36) - Once a week, remove the upper part as well
and wash it with lukewarm water.
10 CLEANING
Maintenance and cleaning must be performed only
when the machine has cooled down and has been
disconnected from the power supply.
•• Do not immerse the machine in water nor place any of its
parts in a dishwasher.
•• Do not use spirit, solvents and/or aggressive chemical
agents.
•• We recommend cleaning the water tank and  lling it up
with fresh water daily.
•• (Fig.20) - After heating milk, brew a small quantity of hot
water as well.
Danger! If the end part of the cappuccinatore has
been removed, do not eject steam.
•• (Fig.22 - 23) - Clean the cappuccinatore weekly.
In order to do this, please:
- Remove the cappuccinatore end part.
- Separate the cappuccinatore upper and lower parts.
- Wash all the cappuccinatore parts with lukewarm
water.
- Wash the suction pipe with a damp cloth and remove
any milk residue.
- Assemble the cappuccinatore.
- Place the end part of the cappuccinatore in the coupling
on the machine (make sure it is completely inserted).
•• (Fig.24) - Empty and clean the drip tray daily.
•• Use a damp and soft cloth to clean the appliance.
•• (Fig.17) - To clean the pressurized portafilter do as
•• 22 ••
follows:
- (Fig.10) - Remove the  lter, wash it thoroughly with hot
water.
- (Fig.10) - Remove the adapter (if fitted), wash it
thoroughly with hot water.
- Remove the pin, wash it thoroughly with hot water.
- Wash the internal part of the pressurized porta lter.
•• Do not dry the machine and/or its components in a
microwave and/or in a conventional oven.
11 DESCALING
The formation of limescale inside the appliance is
inevitable. It is necessary to descale the machine every
3-4 months of use and/or when you notice a reduction in
the water delivery.
If you want to descale the machine yourself,
you can use a non-toxic and/or non-harmful
descaling product for coffee machines (commercially
available). We recommend using Saeco descaling
solution.
Warning! Do not use vinegar as a descaling
solution.
•• (Fig.1) - Remove and empty the water tank.
•• (Fig.2) - Mix the descaling solution with water as speci ed
on the descaling solution box and  ll the water tank. Fit
the tank into the machine.
•• (Fig.3) - Turn on the machine by pressing the ON/OFF
button (2).
•• Wait for the buttons (15 - 16) to be permanently on.
•• (Fig.29 - 30) - Remove the cappuccinatore.
- Loosen the ring nut without taking it off.
- Remove the cappuccinatore coupling from the steam
spout.
•• Place a container under the steam spout.
•• (Fig.5 - 6) Open the knob (4) and press the button (17) to
remove at intervals (one cup at a time) all the descaling
solution.
To stop dispensing, press the button (17) and close the
knob (4).
•• (Fig.3) - During each interval disconnect the machine
by pressing the ON/OFF button (2) in order to let the
descaling solution take effect for about 10-15 minutes.
Empty the container.
•• (Fig.1 - 2) - When the descaling solution is  nished,
remove the water tank, rinse it and  ll it with fresh drinking
water.
•• (Fig.4) - Reinsert the tank into the machine.
•• (Fig.3; Fig.5) - Open the knob (4) and press the button
(17) to empty 2/3 of the water. Press the button (17) and
close the steam knob (4) to stop dispensing.
•• Let the machine warm up and empty the water tank as
described above.
•• Install the cappuccinatore again.
- Insert the cappuccinatore coupling from steam spout
completely.