Operating Information - Telwin FLASH START 700 Bedienungsanleitung

INSTRUCTION MANUAL
WARNING: READ THE INSTRUCTION MANUAL CAREFULLY
BEFORE USING THE STARTER!
1. GENERAL SAFETY USER INSTRUCTIONS FOR THIS
STARTER
In order to reduce the risk of personal injury and damage
to equipment, it is highly recommended to comply with all
essential safety measures and precautions when using the
starter.
- Inexperienced and untrained personnel should be properly
instructed before using the appliance.
- Children must be supervised to prevent them from playing
with the appliance.
- Read carefully and follow the instructions provided in the
manual of the vehicle to be started: the vehicle manufacturer
may indicate what types of emergency starts are permitted
and those to be avoided.
- Protect the eyes. Always wear protective goggles when
using acid lead accumulators.
- Avoid contact with battery acid. If an operator should be
sprayed or come into contact with the acid, rinse the
relative parts immediately under clean running water.
Continue to rinse the area until the physician arrives.
- It is important to connect the cables with the poles in
the right direction:
First connect the red clamp to the positive terminal on
the vehicle battery (+ symbol).
Connect the black clamp to the vehicle chassis or the negative
clamp on the battery, at a distance from the fuel pipe.
- Use the starter in well ventilated areas. Do not attempt to use
the starter when there is gas or inflammable liquids in the
vicinity.
- Do not allow the black and red clamps to come into contact.
- FOR 12 VOLT SYSTEMS ONLY! This device is destined for use
on vehicles running on 12 Volt electrical systems only.
- USE IN EMERGENCY SITUATIONS ONLY: Use it during start-
up operations only.
- Do not work alone. If there is an accident, the assistant can be of
aid to the operator.
- Avoid electrical shocks. Be very cautious when
applying the clamps to non-insulated conductors or bus
bars. Avoid all body contact with surfaces of tubes,
radiators, and metal power substations whilst reading the vehicle
battery voltage.
- Keep the work area clean at all times. Untidy cumbersome areas
can lead to injuries.
- Protect the starter appropriately from all possible damage. It
must only be used as indicated in this Instruction Manual.
- Ensure compliance with the indications in the work area. Do
not use in humid or wet facilities. Never leave it out in the rain.
Always work in well lit areas.
- Keep out of reach of children: they must never be
allowed to access work areas or handle any
machines, instruments or extensions.
- Always wear suitable clothing. Never wear baggy
clothing or jewellery that can get caught up in
moving parts. During all operations, the use of
electrically insulated protection clothing and non-slip boots
must be worn at all times. Persons with long hair must tie it
back and wear a hair net.
- Only experts are allowed to do repair work on the starter as it
involves significant risk levels for inexperienced workers.
- Replacing parts and accessories. When performing maintenance
operations, replace with identical and original spare parts only.
Use of non-original spare parts invalidates all warranties.
- Make sure that the device is always positioned in a stable and
well supported manner.
Never climb over cables or electrical structures.
- Careful attention must be paid during maintaining work on
(EN)
the starter. Check the condition of cables on a regular basis
and if any damage is detected, have the same repaired by an
authorised and qualified technician.
- Check there are no damaged parts. Before using this starter,
carefully check that all seemingly damaged parts and assess
whether or not they can operate correctly. Check that the
cables are securely fastened to the starter. Remember that only
authorised and qualified technicians are allowed to repair or
replace damaged parts.
Keeping this manual.
The manual should be read, paying attention to all the warnings
and safety precautions to be taken when using and maintaining
the device, the list of components and all technical specifications.
Please keep this manual in a secure and dry place for future
reference.
2. INTRODUCTION AND GENERAL DESCRIPTION
Intended use
Portable batteryless starter (super capacitors technology). It starts
a large fleet of vehicles even at low temperatures.
Needs no maintenance as it exploits the residual battery power to
start the vehicle.
Ideal for anyone needing a 12V emergency starter.
Its applications include use on motorcycles, automobiles, boats
and many more.
Fully compatible with any 12-volt starter system.
The starter is fitted with internal devices that protect the user and
the equipment during the starter phase:
- no sparks generated;
- short circuit protection between the clamps;
- protection against polarity inversion.
Description (figure A):
A-1. Starter.
A-2. Starter clamps.
A-3. "ON/OFF" button.
A-4. "GLOW" function button.
A-5. Led indicator.
A-6. Charger cable with cigarette lighter type 12V jack plug.
A-7. 12V charger socket.
A-8. 5V mini USB charger socket.
A-9. Voltage level indicator led.
A-10. Hexagonal key.
3. INSTALLATION
POSITIONING THE STARTER
When using the starter, position it on a horizontal, flat and stable
surface.

4. OPERATING INFORMATION

4.1 How to use the starter:
In most situations, the vehicle's run down battery is still able
to provide the power required for a complete charge of this
starter.
WARNING:
meticulously, and always in the order given
below!
Always prevent the black and red clamps from touching each
other or a common cable!
- Make sure that the vehicle or boat to be started is switched off
(switch or ignition key in the OFF position).
- Connect the red clamp POS. (+) to the battery terminal POS. (+),
then connect the black clamp NEG. (-) to the vehicle chassis or
the battery terminal NEG. (-), at a distance from the fuel pipe.
- The LED indicator (fig. A-9) comes on automatically to indicated
the vehicle battery voltage level.
- Press the ON/OFF button (fig. A-3), the starter will start to
charge: the indicator in figure A-9 now displays the starter charge
status.
- Wait until the GREEN 14V LED stops flashing and remains ON.
- Start the engine.
WARNING: failure to follow these rules may
compromise the operating life of the device:
- Turn the vehicle ignition to the start position for no more
- 3 -
follow these instructions