SWR Black Beauty Bedienungsanleitung Seite 12

EFFECTS BLEND CONTROL
The Effects Blend Control "blends" the signal sent from your instrument with the signal coming from your EXTERNAL effects unit. (In
other words, it has nothing to do with the SubWave™ effect onboard your Black Beauty.) With the Effects Blend fully counter-clock-
wise ("DRY"), no signal from your external effects unit will be heard. As you turn this control clockwise, more of the effect can be
heard in the overall sound. When the Effects Blend control is set fully clockwise ("WET"), no true or unaffected signal is heard other
than what your external effects unit provides. If your external effects unit has a similar control, adjust it to the fully clockwise ("WET")
position. This will avoid any possible phasing problems.
The Effects Blend circuit is similar to that used on recording consoles with the effects loop on a "side chain" to the normal circuit.
Unless the control is set to the full "wet" position, you will always get the full sound of your instrument AND get the diversity an
effects unit offers. This circuit is also effective in reducing noise generated by effects units because it is located after the gain
stages in the preamp.
The Effects Blend control functions only when the Effects Loop is being used. It is activated when a 1/4" phone plug is inserted into
the Effects Receive jack. (For more information, please see "Effects Loop" in the "Rear Panel Features" section later in this guide.)
LIMITER/COMPRESSOR CIRCUIT
The Limiter found in the Black Beauty is a soft knee type limiter. The Limiter circuit is located after (post) the Master Volume and
before (pre) the power amplifier. Therefore, the Limiter is driven by the Master Volume control. Its threshold (starting point) is preset
by the factory so that the user can get maximum overall apparent volume without unduly overdriving (or "clipping") the power amplifi-
er, which can eventually damage the unit's internal circuitry. This can also be helpful in preventing speaker damage when running your
system at high volumes.
ACTIVATING OR DEFEATING THE LIMITER CIRCUIT
You may either activate or defeat the Limiter circuit via the Effects Blend control, which doubles as an on/off switch for the Limiter.
The "In" position activates the Limiter Circuit, and is the default setting as shipped from the factory. To defeat the Limiter, simply pull
"out" on the knob of this control until you hear and feel a "click." To re-engage the Limiter, push the control back in to its original posi-
tion.
LIMITER ACTIVE LED
When the threshold (starting point) of the Limiter circuit is reached, the Limiter Active LED will light, indicating that the Limiter Circuit
is active and helping to protect your power amplifier from clipping. The Limiter LED will not illuminate when: a) The Limiter has been
defeated by pulling out on the Effects Blend control; b) When playing at levels not high enough to engage the circuit.
Note: If you have defeated the Limiter and you hear a loud, sharp distortion present in your sound—and the Preamp Clip LED is
not lighting up—re-engage the Limiter by pushing the Effects Blend control back in. If the distortion goes away, you were proba-
bly clipping the power amp, which is not a good thing. Remember, the Limiter circuit is there to protect your amplifier from such
a state of operation.
MASTER (VOLUME) CONTROL
The Master (meaning "Master Volume") control adjusts the level being sent to the power amplifier in your Black Beauty—it controls the
overall volume of the unit. Turning the control counter-clockwise reduces the overall level, while turning the control clockwise boosts
the overall level.
Two notes: The Master control never affects the level present at the various audio output jacks on the rear panel—it only affects the
level being sent to the power amplifier, and subsequently, your internal speaker and extension speaker outputs only. Also, losses
caused by external effects units can be recovered by increasing the Master control.
POWER ON/OFF SWITCH
This switch turns the complete unit on or off. Setting the switch upwards to the "On" position turns on the unit, and the switch itself
will illuminate in red. Setting the switch downward to the "Power" position will turn the unit off, and the red light inside the power
switch will turn off as well.
12 • BLACK BEAUTY