Technical Data; Dimensions, Weights, Ambient Conditions; Supply Voltage (External); Control Signal - Balluff BTL6-P111-M-A1-S115 series Datenblatt Und Anleitung

BTL6-P111-M_ _ _ _-A1-S115
Micropulse AT Transducer in round profile housing
8

Technical Data

The following are typical values at DC 24 V and 25 °C. Fully operational after power-up, with full accuracy after warm-
up. Values are with BTL6-A-3800-2 or BTL6-A-3801-2 at a constant offset from the transducer:
Resolution < 10 µm
Repeatability < 20 µm
Repeat accuracy < 10 µm
Non-linearity:
NL < 500 mm > 500 mm
< ±200 µm < ±0.04 % FS
typ. ±0.02 % FS
Temperature coefficient
< (6 µm + 5 ppm * NL)/K
NL = nominal length in [mm]
8.1 Dimensions, weights,
ambient conditions
Nominal length < 1500 mm
➥ ➥ ➥ ➥ ➥ page 3
Dimensions
Weight approx. 1.0 kg/m
Housing anodized aluminum
Operating temp. 0 °C to +70 °C
Humidity < 90%, non-condensing
Protection class
per IEC 60529 IP 67
when closed up
Shock loading 50 g/6 ms
1
per IEC 60068-2-27
Continuous shock 50 g/2 ms
1
per IEC 60068-2-29
Vibration 12 g, 10 to 2000 Hz
1
per IEC 60068-2-6
1 Individual specifications as per
Balluff factory standard
8.2

Supply voltage (external)

Regulated supply
voltage DC 20 ... 28 V
Ripple < 0.5 V
ss
Current draw < 60 mA (at 1 kHz)
Inrush < 3 A/0.5 ms
Polarity reverse protection 1.5 * U
8.3

Control signal

INIT pulse
Level +5 V RS 422-driver
Pulse widths
measurement mode 1 to 5 µs
data protocol mode approx. 15 µs
Sampling rate 0.5 to 2 kHz
Polarity reverse protection 1.5 * U
8 8
english
8.4

Position signal

START/STOP pulse
Level +5 V RS 422-driver
Pulse widths
Polarity reverse protection 1.5 * U
8.5

Overvoltage protection

Dielectric strength 500 V
to housing
Polarity reverse protection 1.5 * U
8.6

Included in shipment

Transducer with condensed guide
Magnets, mounting brackets and
connection cable must be ordered
separately.
8.7

Magnet

(order separately)
BTL5-A-3800-2
Weight approx. 30 g
BTL5-A-3801-2
Weight approx. 25 g
Housing plastic
Spacing, offset and installation
Operating temp. 0 °C to +70 °C
8.8 Connection cables,
connectors
(order separately)
Shielded cable with connector on
one end
straight: BKS-S115-PU-_ _
right-angle: BKS-S116-PU-_ _
_ _ = length L, 02, 05, 10, 20
05 means L = 5 m
B Wiring assignments ➥ Table 4-1
Connector for
shielded cable
straight: BKS-S115-00
Wiring assignments
B
8.9

Mounting brackets

(order separately)
BTL6-A-MF03-K-50
3 to 5 µs
BTL6-A-MF01-A-50
B
BTL6-A-MF01-A-43
B
7.5
15
Fig. 8-1: Mounting bracket
BTL6-A-MF01-A-50
➥ ➥ ➥ ➥ ➥ Fig. 3-1
➥ ➥ ➥ ➥ ➥ Fig. 3-2
7.5
15
➥ ➥ ➥ ➥ ➥ page 3
Fig. 8-2: Mounting bracket
BTL6-A-MF01-A-43
8.10 Compatible processors
and displays
Analog output processor cards:
➥ ➥ ➥ ➥ ➥ Fig. 4-2
BTM-A1 multi-channel processor
card with 1 to 4 DC analog outputs
Digital output processor cards:
BTA-H11
BCD, Gray/binary or
SSD, Gray
➥ Fig. 4-3
Displays:
BDD-07-9 digital display,
➥ Table 4-1
7-digit for BTA-H
BDD-AM10-1-P display and
controller with 2 relay outputs
BDD-CC08-1-P display and
controller with 8 setpoints
➥ Fig. 3-1
➥ Fig. 8-1
➥ Fig. 8-2
35
Ø 5.5 +0.2 50 ±0.2
60 –0.3
32 –0.3
Ø 3.7 +0.2 35
42.7 ±0.2
57 –0.3
22 bit,