Fuels Refuelling - Makita DCS 9000 Wichtige Änderungen Zur Betriebsanweisung

0
Fuels
/ Refuelling
Fuel
I
50:l
I
EN+
1000
cm3
(1
litre) 20 cm3
5000
cm3
(5
litres)
100
cm3
4 0 : l
25 cm3
125 cm3
250 cm3
Fuel
mixture
The engine of the chain saw is a high-efficiency two-stroke
engine. It runs on a mixture of gasoline and two-stroke engine
oil.
The engine is designed for unleaded regular gasoline with a min.
octane value of 91 ROZ. In case no such fuel is available, you
can use fuel with a higher octane value. This will not affect the
engine.
In order to obtain an optimum engine output and to protect
your health and the environment use unleaded fuel only.
For lubricating the engine use a two-stroke engine oil (quality
grade: TC-3), which is added to the fuel. The engine has been
designed for use of MAKITA high-performance two-stroke en-
gine oil and a mixture ratio of only
50:l
to protect the environ-
ment. In addition, a long service life and reliable operation with
a minimum emission of exhaust gases are ensured.
MAKITA high-performance two-stroke engine oil is available in
the following sizes to suit your individual requirements:
1 I ordernumber 980008607
100 ml order number
980 008 606
In case MAKITA high-performance two-stroke engine oil is not
available, it is urgently recommended to use a mixture ratio of
40:1, as otherwise optimum operation of the engine cannot be
guaranteed.
The correct mixture ratio:
50:l
4 0 : l
when using MAKITA high-performance two-stroke engi-
ne oil, i. e. mix 50 parts gasoline with 1 part oil.
when using other two-stroke engine oils, i. e. mix40 parts
gasoline with 1 part oil.
NOTE:
For preparing the fuel-oil mixture first mix the entire oil quantity
with half of the fuel required, then add the remaining fuel.
Thoroughly shake the mixture before filling it into the chain saw
tank.
It is not wise to add more engine oil than specified to ensure safe
operation. This will only result in a higher production of combus-
tion residues which will pollute the environment and clog the
exhaust channel in the cylinder as well as the muffler. In
addition, fuel consumption will rise and performance will de-
crease.
A
BIO
TOP
Chain oil
Use an oil with adhesive additive for lubricating the chain and
guide bar. The adhesive additive prevents the oil from being
flung off the chain too quickly.
We recommend the use of chain oil which is bio-degradable in
order to protect the environment. The use of bio-degradable oil
may even be required by local regulations.
The chain oil BIOTOP sold by MAKITA is made of special
vegetable oils and is 100% bio-degradable. BIOTOP has been
granted the "blue angel" (Blauer Umweltschutz-Engel) for being
particularly environment-friendly (RAL UZ 48).
BIOTOP chain oil is available in the following sizes:
1 I order number 980 008 610
5 I order number 980 008 61 1
order number
980 008 613 20 I
Bio-degradable oil is stable only for a limited period of time. It
should be used within 2 years from the date of manufacture
(printed on the container).
Important note on bio-degradable chain oils:
If you are not planning to use the saw again for an extended
period of time (longer than the expiration date of the chain oil),
empty the oil tank and put in a small amount of regular engine
oil (SAE
30),
and then run the saw for a time. This is necessary
to flush out all remaining bio-degradable oil from the oil tank, oil-
feed system, chain and guide bar, as many such oils tend to
leave sticky residues over time, which can cause damage to the
oil pump or other parts.
The next time you use the saw, fill the tank with BIOTOP chain
oil again.
NEVER USE WASTE OIL
Waste oil is very dangerous for the environment.
Waste oil contains high amounts of carcinogenic substances.
Residues in waste oil result in a high degree of wear and tear at
the oil pump and the sawing device.
In case of damage caused by using waste oil or unappropriate
chain oil the product guarantee will be null and void.
Your salesman will inform you about the use of chain oil.
12