Femi N215 XL Gebrauchsanleitungen Seite 13

O Vice
P Clamp drive
Q Vice speed-slide drive
R Column
UNIVERSAL MOTOR VERSION
WEIGHT: ............................................................... 140 Kg.
SIZE:.............................................cm 575 x 670 x H 720
....................................... in maximum overall dimensions.
PACKAGING SIZE: .........................cm 780x1240xH1080
INDUCTION MOTOR VERSION
WEIGHT: ............................................................... 150 Kg.
SIZE:..............................................cm 575 x 670 x H 720
....................................... in maximum overall dimensions.
PACKAGING SIZE: .........................cm 780x1240xH1080
2 INSTALLATION
2.1 REMOVING THE PACKING
The machine is delivered inside a box suitable for the
purpose.
Therefore, the packing must be removed completely by
means of suitable tools and care must be take in order to
avoid damage to any part of the machine.
For packing disposal, please refer to 6.4 point.
2.2 HANDLING AND TRANSPORTION (Fig. 2)
The machine and must be moved only using suitable lifting
devices.
WARNING: Do not try to move or lift the machine
by hand even if more people are present.
WARNING: The operations described in this
manual relative to sling, transport and lifting
by means of a fork lift or hoist must be carried
out only by skilled and qualified personnel
(EC/2006/42).
To move the machine while it is still inside the packing, use
a fork lift by inserting the two forks in the rooms provided
under the bearing board
Move the machine carefully and avoid sudden movements
which could unbalance the load and make it drop.
To remove the machine from the plate after packing removal,
loosen the fi xing screws but keep them should the machine
be transported for long stretches.
To transport the machine after freeing it from the plate,secure
it with resistant chains, ropes or braces, by passingthem
through the the eyebolts provided.
Then the machine must be lifted using a hoist of adequate
capacity or through another means suitable for this
purpose.
WARNING: Do not lift the machine by the body
D (Fig. 1).
WARNING: Before lifting the machine, check that
the body is lowered and secured to the rest of
the structure by means of ropes or other claming
means as shown in Fig. 2
2.3 ELECTRICAL CONNECTIONS
Check that the mains to which the machine is connected is
earthed in accordance with current safety regulations and
that the power point is in good condition.
Connect a plug in compliance with safety rules to the
end of the mains cable of the machine, checking that the
yellow/green protective conductor is fi tted into the relative
terminal marked.
INDUCTION VERSION ONLY (Fig. 3): check for the correct
polarity of the motor through the blade which must rotate
in the direction shown by the arrow present on the
machine body. If this is not the case, invert two of the three
cables of the plug.
Mount electric panel A into its seat on the pivoting support,
and finally secure it by tightening the supplied fixing
screws.
Remember that there should be a magnetothermic
protective device fi tted upstream of the mains to protect all
the conductors from short circuits and overloads.
This protective device should be selected according to the
electrical features of the machine stated on the motor.
The motor of your sawing machine is equipped with a
protective heat circuit breaker which interrupts the power
supply when the temperature of the coils rises too high.
When the power supply is interrupted, wait for normal
reset.
UNIVERSAL VERSION (Fig. 4)
In case of power failure in mains, while you wait for power
to be restored there is no danger hazard may arise : in
fact, the electronic speed variator is also equipped with a
reset function which prevents the machine from re-starting
automatically. To start the machine, press the start push
button A on the handgrip twice.
INDUCTION VERSION (Fig. 3-4)
In case of voltage failure in the system, you can wait for
the connection to be restored without danger of hazardous
conditions. In fact, the electric panel is equipped with a
reset function which prevents the machine from restarting
automatically.
To restart the machine, press the button C (Fig. 4) and then
push button A (Fig. 4) on the handgrip.
WARNING: Never change the overload cutout
setting to avoid overloads which could damage
the motor circuits and other mechanical
members.
11