Additional Information - Nice Neomat T Installation

4.4) Memory deletion
If you need to delete all the transmitter and the programmed operations, carry out the procedure shown in table A14.
The memory can be deleted:
• with a non-memorized transmitter starting from point A.
• with a previously memorized transmitter starting from point No. 1.
The following can be deleted:
• only the memorized transmitters, finishing at point No. 4
• all data (transmitters, sensor level, TTBUS address, etc.), completing the procedure until point 6.
Table "A14" Memory deletion
➨
A. Switch the motor off, activate the Step-by-Step input (by connecting the White cable
with the White/Black one) and keep it active until the end of the procedure
B. Power the motor and wait for the initial beeps
➨ Press and hold down button ■ on a transmitter (about 5 seconds) until you hear
1.
a beep; then release it
Hold down the ▲ button on the transmitter until you hear 3 beeps;
2.
release the ▲ button exactly during the third beep
Hold down button ■ on the transmitter until you hear 3 beeps;
3.
release button ■ exactly during the third beep
➨ Hold down the ▼ button on the transmitter until you hear 3 beeps;
4.
release the ▼ button exactly during the third beep.
5. To cancel everything:
Press both ▲ and ▼ within 2 seconds
Cancellation is confirmed by releasing buttons ▲ and ▼ on the first of the 5 beeps
6.

5) Additional information

The NEOMAT-T motors recognise other ERGO, PLANO, NICEWAY and VOLO S RADIO series transmitters (see chapter 5.1 "Available trans-
mitters").
A particular command can also be associated to each transmitter button by means of a specific memorization procedure (see chapter 5.2
"Transmitter programming in Mode I and Mode II").
Warning: use transmitters that have been memorised in Mode 1 only for programming.
5.1) Available transmitters
Table A15 indicates the transmitters that can be used with the relat-
ed coding.
Table "A15"
Transmitters
ERGO1 - ERGO4 - ERGO6
PLANO1 - PLANO4 - PLANO6 - PLANO TIME
VOLO S RADIO
NICEWAY (the whole series)
FLO1R - FLO2R - FLO4R
VERY VR
5.1) Memorizing the transmitters in Mode I and Mode II
Tables "A1" and "A2" describe the memorization of the transmitters in "Mode I" where a specific command is assigned to each button: but-
ton ▲ (1) = "Up"; button ■ (2) = "Stop"; button ▼ (3) = "Down".
The transmitters can also be memorized on "Mode II", which allows greater flexibility in the use of the transmitter buttons. Transmitters can
be memorized both in Mode I and Mode II on the same NEOMAT-T motor.
5.2.1) Mode I
The command associated to the transmitter buttons is fixed in Mode I: button ▲
(1) = "Up"; button ■ (2) = "Stop"; button ▼ (3) = "Down", another button 4 com-
mands the "Stop".
A single memorization phase is performed in Mode I for each transmitter and a sin-
gle section is occupied in the memory. It is not important which button is pushed
when memorizing in Mode I.
Memorizing and deleting the transmitters in Mode I (see Tables A1 and A2).
10
ERGO PLANO
FLO4R VERY
Mode I
Button
Button ▲ or 1
Button ■ or 2
Button ▼ or 3
Button 4
Example
PP
5s
NICEWAY VOLO S RADIO
Command
Up
Stop
Down
Stop