Setup Menu Table - Thermo Scientific Orion Star series Bedienungsanleitung

Meter Setup

Setup Menu Table

The following table is for the complete line of Orion Star and Star Plus meters .
Meters may not include all of the options listed in this table .
Top Line Middle Line
PH rES
PH bUF
ISE rES
ISE UnIt
ISE rAng
ISE nLIn
C0nd tC
C0nd C0EF
C0nd tdSF
C0nd CELL
C0nd trEF
C0nd tyPE
See the RDO Optical Dissolved Oxygen Setup Menu section for details on the RDO probe information menus.
d0 rES
d0 rES
d0 bAr
d0 PrES
d0 SAL
d0 SALF
d0 CALt
d0 LIFE
dUE PH
dUE 0rP
dUE ISE
dUE C0nd
dUE d0
EN-12
Bottom Line
0.1, 0.01, 0.001
USA, EUr0
1, 2, 3
m, mgL, PEr, PPb, n0nE
L0w, HIgH
AUt0, 0FF
0FF, LIn, nLF
0.0 to 10.0
0.00 to 10.0
0.001 to 199.0
5, 10, 15, 20, 25
Std, 1, 2, 3, 4, 5, 6, 7, USP
0.1, 1 % sat
0.01, 0.1 mg/L
AUt0, mAn
450.0 to 850.0
AUt0, mAn
0 to 45
AIr, H20, mAn, SEt0
365 to 0
0 to 9999
0 to 9999
0 to 9999
0 to 9999
0 to 9999
Thermo Scientific Orion Star
Setup Menu Description (default setting, method specific)
pH measurement resolution (0.01, yes)
pH buffer set for automatic buffer recognition during calibration,
USA buffers are 1.68, 4.01, 7.00, 10.01, 12.46 and EUrO buffers
are 1.68, 4.01, 6.86, 9.18 (USA, yes)
ISE measurement resolution in significant figures (1, yes)
ISE measurement units (PPb, yes)
ISE concentration range for calibration stability criteria (HIgH, yes)
ISE automatic blank correction for low-level calibration (AUt0, yes)
Conductivity temperature compensation type, LIn is for linear,
nLF is for non-linear pure water samples (LIn, yes)
Conductivity temperature compensation coefficient in % change
in conductivity per °C, appears if LIn was selected for tC (2.1, yes)
Conductivity TDS factor value (0.49, yes)
Conductivity default cell constant value for automatic conductivity
calibration mode (0.475, yes)
Conductivity reference temperature (25, yes)
Conductivity cell type and selectable range. Std is for standard,
USP is for planar, 1 through 7 for fixed ranges (Std, yes)
DO % saturation measurement resolution (0.1, yes)
DO mg/L measurement resolution (0.01, yes)
DO barometric pressure compensation type (AUt0, yes)
DO manual barometric pressure compensation value, appears
if mAn was selected for bAr (760.0, yes)
DO salinity correction type (AUt0, yes)
DO manual salinity correction value, appears if mAn was selected
for SAL or a DO meter without a conductivity mode is used (0, yes)
DO calibration type (AIr, yes)
Optical cap replacement countdown in days – 3, 4 and 5 Star Plus
RDO meters only (Set by RDO probe, no)
pH calibration alarm value in hours, 0 is off (0, yes)
ORP calibration alarm value in hours, 0 is off (0, yes)
ISE calibration alarm value in hours, 0 is off (0, yes)
Conductivity calibration alarm value in hours, 0 is off (0, yes)
DO calibration alarm value in hours, 0 is off (0, yes)
and Star Plus Meter User Guide
™