Declaration Of Ce-Conformity; Name: Torsten Bröker - WALTHER PILOT PILOT WA 400 Betriebsanleitung

Contents
Exploded Drawing

Declaration of CE-Conformity

Replacement parts
1 General
1.1 Identification of Model Version
1.2 Normal Use
1.3 Improper Use
2 Technical Description
3 Safety Warnings
3.1 Safety Warting Symbols
3.2 Generally Applicable Safety Precautions
4 Assembly / Installation
4.1 Mounting of Spray Gun
4.2 Connection of Input Lines
5 Operational Handling
5.1 Safety Warnings
5.2 Starting/Stopping Requirements
5.3 Spray Pattern Test
5.4 Spray Pattern Adjustments
5.5 Retooling of Spray Gun
6 Cleaning
6.1 Safety Warnings
6.2 Cleaning - Complete
6.3 Cleaning - Routine
7 Repairs / Replacements
7.1 Replacement of defective Needle Seal Packings
7.2 Replacement of Nozzles, Needles, Springs and Seals
8 Trouble shooting and Corrective Action
9 Disposal of Cleaning / Servicing Substances
10 Specification Data
2
27
28
32
32
32
33
34
34
34
35
36
36
36
37
37
37
37
38
40
40
40
41
42
42
43
43
44
44
45
26
Declaration of CE-Conformity
We, the manufacturers of the equipment, hereby declare under our sole responsibility that
the product(s) described below conform to the essential safety requirements. This declaration will
be rendered invalid if any changes are made to the equipment without prior consultation with us.
Manufacturer WALTHER Spritz- und Lackiersysteme GmbH
Kärntner Str. 18 - 30
D - 42327 Wuppertal
Tel.: +49(0)202 / 787 - 0
Fax: +49(0)202 / 787 - 2217
www.walther-pilot.de • e-mail: info@walther-pilot.de
Type Designation Automatic Spray Guns
WA 400
WA 410
WA 420
WA 430
WA 470-K (Adhesive application version)
WA 471-K (Ad. application version - circulation)
WA 472-K (Ad. application version - low-pressure)
WA 473-K (Ad. appl. vers. - low-pressure - circulation)
Intended purpose Processing of sprayable media
Applied Standards and Directives
EU-Mechanical Engineering Directives 2006 / 42 / EC
94 / 9 EC (ATEX Directives)
DIN EN ISO 12100-1
DIN EN ISO 12100-2
DIN EN 1127-1
Specification according 94 / 9 / EC
Category 2 Part marking
Authorized with the compilation of the technical file:
Nico Kowalski, WALTHER Spritz- und Lackiersysteme GmbH, Kärntner Str. 18 - 30
D- 42327 Wuppertal
Special remarks :
The named product is intended for installation in other equipment. Commissioning is prohibited
until such time as the end product has been proved to conform to the provision of the Directives
2006 / 42 / EC.
Wuppertal, the 1st of January 2010
i.V.

Name: Torsten Bröker

Position: Manager, Design and Development
This Declaration does not give assurance of properties in the sense of product liability. The safety instructions
provided in the product documentation must be observed at all times.
(Standard version)
(Circulation version)
(Low-pressure version)
(Low-pressure and circulation vers.-standard)
DIN EN 1953
DIN EN 13463-1
Tech.File,Ref.:
II 2 G c T 5
27
20 540
20 541
20 542
20 543
20 580
20 581
20 582
20 583
2407