Loading Programs From A Usb Storage Device; Midi Control; Adjusting The Midi Channel (Midi Ch); Controlling The Unit By Means Of Midi Signals - Leuchtkraft DMX-3216 Bedienungsanleitung

3) Press the number button of the program to be
saved . If a program has already been saved to
this number, it will be overwritten .
will appear on the display; a status bar in the
lower line will indicate the progress of the save
process .
Once the program has been saved,
Saved OK
Repeat steps 2 and 3 to save further programs .
6.4 Loading programs from a
USB storage device
To load a program from a USB storage device onto
the storage of the controller:
1) Connect the USB storage device to the jack
USB (27) .
2) Keep the buttons MODE (20) and  (13)
pressed for 3 s .
on the display . The LEDs above the number
buttons (17) to which programs have already
been saved on the storage device used will
light up .
If the storage device connected is not com-
patible,
NO Disk
3) Press the number button of the program to
be loaded . If a program with this number
has already been saved to the storage of the
controller, it will be overwritten .
will appear on the display; a status bar in the
lower line will indicate the progress of the load
process .
Once the program has been loaded,
Loaded OK
If a number is selected where no pro-
gram has been saved on the storage device,
FILE Error!
display .
Repeat steps 2 and 3 to load further programs .

6.5 MIDI control

The DMX-3216 may be remote-controlled by
means of a MIDI signal . In addition, the control-
ler, if operated directly, generates MIDI signals at
the output MIDI OUT (29) that can, for example,
control a second DMX-3216 . For this, first select
the MIDI channel to which the controller is to
respond or on which the controller is to send
MIDI signals .
26
will briefly appear on the display .
Loading File
will appear on the display .
will briefly appear on the display .
will briefly appear on the

6.5.1 Adjusting the MIDI channel (MIDI CH)

1) Keep the button TAP (15) pressed for 3 s .
Writing
The LED above the button will start to flash;
MIDI ADDR:
will appear on the display .
2) Use the control WAIT TIME (24) to adjust the
MIDI channel desired (1 – 16) .
3) Keep the button TAP pressed until the LED
above the button stops flashing .
6.5.2 Controlling the unit by means of
1) To activate the MIDI control for the controller,
keep the button MIDI IN (14) pressed and also
press the button  (13) . The LED next to the
button MIDI IN will light up;
will appear on the display
by means of MIDI commands (
will appear
2) To deactivate MIDI control, keep the button MIDI
IN pressed and also press the button  . The
LED next to the button MIDI IN will extinguish .

6.6 Resetting the unit

Caution: The following procedure will delete all
scenes and all programs . All adjustments the user
may have made will be reset to their factory set-
tings . If required, save the programs on an external
device (
1) Switch off the controller .
Writing
2) Keep the buttons MODE (20) and DEL (21)
pressed and switch on the controller . All LEDs
will flash briefly to confirm the procedure .
3) Release the buttons .

7 Specifications

Data protocol: . . . . . . . . . . DMX 512
Number of DMX channels: . 512
Connections
DMX output:. . . . . . . . . . XLR jack, 3 poles
Audio input: . . . . . . . . . . 0.1 – 1 Vpp, RCA
USB: . . . . . . . . . . . . . . . . jack type A
MIDI IN, OUT, THRU: . . . . DIN jacks, 5 poles
Power supply: . . . . . . . . . . via power supply unit
Ambient temperature: . . . . 0 – 40 °C
Dimensions: . . . . . . . . . . . 482 × 134 × 80 mm, 3 RS
Weight: . . . . . . . . . . . . . . . 2.4 kg
xx (xx = current MIDI channel)
MIDI signals
The controller can now be remote-controlled
☞ chapter 6 .3) prior to resetting the unit .
provided, connected to
230 V/ 50 Hz
MIDI In Mode
☞ chapter 7 .1) .