Optional Accessories - Nice E Plus M Installierungs-Und Gebrauchsanleitungen Und Hinweise

01
5
sec.
03
x 1 = vento a 5 Km/h
x 1 = wind at 5 Km/h
x 2 = vento a 10 Km/h
x 2 = wind at 10 Km/h
x 3 = vento a 15 Km/h (*)
x 3 = wind at 15 Km/h (*)
0,5
x 4 = vento a 30 Km/h
x 4 = wind at 30 Km/h
sec.
x 5 = vento a 45 Km/h
x 5 = wind at 45 Km/h
Note: • When performing the procedure, you can cancel it at any time by keeping the n and t keys pressed simultaneously for 4 seconds. Otherwise, do not press
any key and wait 60 seconds for the motor to perform 6 movements. • If you use a sensor equipped with a "trimmer", you must read the sensor instructions and ad-
just the threshold directly on the sensor.
01
PRG
1
sec.
04
x 1 = vento a 5 Km/h
x 1 = wind at 5 Km/h
x 2 = vento a 10 Km/h
x 2 = wind at 10 Km/h
x 3 = vento a 15 Km/h (*)
x 3 = wind at 15 Km/h (*)
0,5
x 4 = vento a 30 Km/h
x 4 = wind at 30 Km/h
sec.
x 5 = vento a 45 Km/h
x 5 = wind at 45 Km/h
(*) - Factory setting
6

OPTIONAL ACCESSORIES

6.1 - Control pushbutton strip (wall-mounted)
6.1.1 - Installation of the pushbutton strip
this accessory can be used as an alternative to the radio transmitter to send, by wire,
the controls to the motor when using the automation.
Installation warnings:
• it is recommended to use an unstable pushbutton strip with interlocked pushbut-
tons.
• The mechanical operation of the push buttons must be exclusively of the "with op-
erator present" type: in other words, and they are released, they must return to
their initial position. Note – When the stop positions have been adjusted, all you
need to do is simply press the key start the shutter/awning moving, after which it
will stop automatically when it reaches the programmed stop position.
• You can choose models with one or two pushbuttons according to your needs:
The model with two push buttons activates the Raise and Lower input; the model
with one pushbutton can activate the TTBus / Open / Step-to-step (the type of in-
put is selected with the procedure described in paragraph 13).
• The keypad must be located...
– in a place that is not accessible to outsiders/strangers;
– in sight of the shutter/awning, but out of the reach of its moving parts;
– on the side of the shutter/awning housing the motor cable and mains power ca-
ble (fig. 6-h);
– at a height no less than 1.5 m from the floor/ground.
14 – English
2
10
sec.
––– Procedure 5.17 ––– executable only with a series transmitter Era P and Era W
02
PRG
1
2
sec.
10
sec.
02
5
3
sec.
1 /
2 /
3 /
4 /
?
5 /
03
5
2
sec.
05
1 /
2 /
3 /
4 /
?
5 /
6.1.2 - Connecting the pushbutton strip
A - PUSHBUTTON STRIP WITH 2 PUSH BUTTONS (wires to use: White +
White-Orange + White-black): to connect this accessory, see fig. 5.
B - PUSHBUTTON STRIP WITH 1 PUSH BUTTONS (wires to use: White +
White-black): to connect this accessory, see fig. 5. Once you have complet-
ed the hookup, run the procedure given in par. 5.13 to allocate the "Open" or
"Step-by-step" command to the key.
WARNING! – The maximum length of the cables used to connect a wall-mounted
panel or a relay is 100 m.
6.2 - Climate sensors for wind, sun, rain
WARNING! – Only radio-based sensors can be used. These accessories inde-
pendently control the movements of the awning/shutter according to the atmospheric
conditions detected outdoors.
Warning – These climate sensors must not be considered as safety devices that
can eliminate failures in the awning/shutter caused by the effects of rain or strong
winds; a mere electricity blackout, in fact, would make the automatic movement of
the awning/shutter impossible. Consequently, these sensors must be considered as
components of the automated device, that are useful in protecting the awning/shut-
ter. Nice declines all liability for any material damages that occur due to atmospheric
events not detected by the sensors.
6.2.1 - Definitions and conventions
• Manual "Sun On" Command = enables the reception, by the motor, of auto-
matic commands transmitted by the "Sun" sensor if present in the installation.
When reception is enabled, the user can send manual commands at any time:
these override the automatic operation of the automated device.
04
5
3
sec.
3
5
3
sec.