Intended Use - DeWalt XR LI-ION DCS391 Bedienungsanleitung

Rip guide knob
15
Rip guide
16

Intended Use

Your DCS391 cordless circular saw has been designed for
professional wood sawing applications.
DO nOT use under wet conditions or in the presence of
flammable liquids or gases.
These heavy-duty circular saws are professional power tools.
DO nOT let children come into contact with the tool.
Supervision is required when inexperienced operators use
this tool.
Young children and the infirm. This appliance is not
•
intended for use by young children or infirm persons
without supervision.
• This product is not intended for use by persons (including
children) suffering from diminished physical, sensory or
mental abilities; lack of experience, knowledge or skills
unless they are supervised by a person responsible for their
safety. Children should never be left alone with this product.
ASSEMBLY AND ADJUSTMENTS

WARNING: To reduce the risk of serious personal
injury, turn tool off and disconnect battery pack
before making any adjustments or removing/
installing attachments or accessories. An accidental
start-up can cause injury.

WARNING: Use only D
e
Inserting and Removing the Battery Pack
from the Tool (Fig. B)
nOTE: Make sure your battery pack
To Install the Battery Pack into the Tool
Handle
1. Align the battery pack 3 with the rails inside the tool's
handle (Fig. B).
2. Slide it into the handle until the battery pack is firmly seated
in the tool and ensure that you hear the lock snap into place.
To Remove the Battery Pack from the Tool
1. Press the release button 13
out of the tool handle.
2. Insert battery pack into the charger as described in the
charger section of this manual.
Fuel Gauge Battery Packs (Fig. B)
Some D WALT battery packs include a fuel gauge which
e
consists of three green LED lights that indicate the level of
charge remaining in the battery pack.
To actuate the fuel gauge, press and hold the fuel gauge button
22 . A combination of the three green LED lights will illuminate
designating the level of charge left. When the level of charge
in the battery is below the usable limit, the fuel gauge will not
illuminate and the battery will need to be recharged.
WALT battery packs and chargers.
3 is fully charged.
and firmly pull the battery pack
nOTE: The fuel gauge is only an indication of the charge left on
the battery pack. It does not indicate tool functionality and is
subject to variation based on product components, temperature
and end-user application.
Trigger Switch (Fig. A)

WARNING: This tool has no provision to lock the trigger
switch in the ON position and should never be locked ON
by any other means.
Release the trigger switch lock-off button
button as shown. Pull the trigger switch
Releasing the trigger switch turns the motor off.
Depth of Cut Adjustment (Fig. A, C)
1. Loosen the depth adjustment lever
2. Move the shoe to obtain the correct depth of cut.
5
3. Tighten the depth adjustment lever
4. For optimal results, allow the saw blade to protrude from
the workpiece by about 3 mm (see inset in figure C).
Bevel Adjustment (Fig. D)
The bevel angle can be adjusted between 0° and 50°.
1. Loosen the bevel adjustment knob
2. Set the bevel angle by tilting the saw shoe
indicates the desired angle on
the scale.
3. Tighten the bevel adjustment knob
Shoe Adjustment for 90° Cuts (Fig. A, E)
1. Adjust the saw to 0° bevel.
2. Retract the blade guard using the lever
on the blade side.
3. Loosen the bevel adjustment knob
4. Place a square against the blade and shoe to adjust the
90° setting.
5. Turn the calibration screw
the proper angle.
6. Confirm the accuracy of the setting by checking the
squareness of an actual cut on a scrap piece of material.
Rip Guide Installation and Usage (Fig. F)
Ripping is the process of cutting wider boards into narrow
strips, cutting the grain lengthways. Hand guiding is more
difficult for this type of sawing and the use of the rip guide
i recommended.

WARNING: For your own safety, read the instruction
manual before using any accessory. Failure to heed
these warnings may result in personal injury and serious
damage to the saw and accessory. When servicing this
tool, only use identical replacements.
Assembly
1. Loosen the rip guide knob
2. Insert the rip guide as shown in figure F.
16
3. Tighten the rip guide knob
EngLIsh
1 by pressing the
2 to turn the motor on.
4 .
4 .
.
10
5 until the mark
10 .
6 and place the saw
.
10
17 so that the shoe will stop at
15 .
15 securely.
37