Intended Use - DeWalt RX li-ion DCS396 Übersetzt Von Den Originalanweisungen

EngLIsh
1 Instruction manual
• Check for damage to the tool, parts or accessories which may
have occurred during transport.
• Take the time to thoroughly read and understand this manual
prior to operation.
Markings on Tool
The following pictograms are shown on the tool:
Read instruction manual before use.
Wear ear protection.
Wear eye protection.
Do not expose the power tool to humidity.
Date Code Position (Fig. A)
The date code , which also includes the year of manufacture,
17
is printed into the housing.
Example:
2016 XX XX
Year of Manufacture
Description (Fig. A, B)

WARNING: Never modify the power tool or any part of it.
Damage or personal injury could result.
On/off trigger switch
1
Lock-off button
2
Rear grip handle
3
Front handle
4
Saw blades
5
Bar
6
Hex key
7
Dust port
8
Battery
9
Battery release button
10

Intended Use

Your D WALT alligator saw has been designed for professional
e
sawing applications of clay building blocks, cellular concrete,
wood, plastic and insulation materials with suitable saw blade.
DO nOT use under wet conditions or in the presence of
flammable liquids or gases.
These alligators aws are professional power tools.
DO nOT let children come into contact with the tool.
Supervision is required when inexperienced operators use
this tool.
• Young children and the infirm. This appliance is not
intended for use by young children or infirm persons
without supervision.
34
• This product is not intended for use by persons (including
children) suffering from diminished physical, sensory or
mental abilities; lack of experience, knowledge or skills
unless they are supervised by a person responsible for their
safety. Children should never be left alone with this product.
ASSEMBLY AND ADJUSTMENTS

WARNING: To reduce the risk of serious personal
injury, turn tool off and disconnect battery pack
before making any adjustments or removing/
installing attachments or accessories. An accidental
start-up can cause injury.

WARNING: Use only D
e
Inserting and Removing the Battery Pack
from the Tool (Fig. B)
nOTE: Make sure your battery pack
To Install the Battery Pack into the Tool
Handle
1. With tool off, align the battery pack
the tool's handle (Fig. A).
2. Slide it into the handle until the battery pack is firmly seated
in the tool and ensure that you hear the lock snap into place.
To Remove the Battery Pack from the Tool
1. Press the battery release button
battery pack out of the tool handle.
2. Insert battery pack into the charger as described in the
charger section of this manual.
Fuel Gauge Battery Packs (Fig. B)
Some D WALT battery packs include a fuel gauge which
e
consists of three green LED lights that indicate the level of
charge remaining in the battery pack.
To actuate the fuel gauge, press and hold the fuel gauge
button . A combination of the three green LED lights will
18
illuminate designating the level of charge left. When the level
of charge in the battery is below the usable limit, the fuel gauge
will not illuminate and the battery will need to be recharged.
nOTE: The fuel gauge is only an indication of the charge left on
the battery pack. It does not indicate tool functionality and is
subject to variation based on product components, temperature
and end-user application.
Replacing the Saw Blades
Removing the Saw Blades (Fig. C–F)
1. Place the tool upside down on a flat, stable work surface.
2. Loosen the gearcase cap screw
When loosened, the gearcase cap
spring open.
3. With the hex key 7 , loosen both of the blade setting
screws 13 . The screws will be held in place by the
screw clips.
4. Carefully pull the saw-blade-end up until it is disengaged
from and clear of the Blade-Clamp-system.
WALT battery packs and chargers.
9 is fully charged.
9 with the rails inside
10 and firmly pull the
11 with the hex key 7 .
should release and
12