Retrofitting/Operation.of.radio.control.system - Becker S80 Bedienungsanleitung

Operating Instructions
Retrofitting/Operation of Radio Control System
Door.control.unit.S80.with.ELS.Professional.Card.3.1.can.be.pro-
vided.with.a.1-channel.or.4-channel.radio.remote.control.system..
If.such.a.system.has.been.ordered.with.the.control.unit,.the.radio.
receiver.will.already.have.been.installed.in.the.control.unit..If.this.is.
the.case,.please.proceed.to.the.section."Operation".
If.a.radio.remote.control.system.is.being.retrofitted,.you.must.first.
install.the.receiver.board.on.the.motherboard..For.this.disconnect.
the.entire.door.control.system.from.the.mains.
Insert.the.radio.control.receiver.board.in.slot.J1.at.the.top.right.of.
the. S80. motherboard,. as. shown. on. the. drawing.. Make. sure. the.
board.is.the.right.way.round.
Operation
1-channel radio remote control
The.1-channel.radio.remote.control.operates.in.the.same.way.as.the.1-way.pushbutton.switch..The.pushbutton.commands.
are.executed.one.after.the.other.in.the.sequence.UP.-.STOP.-.DOWN.-.STOP..If.there.is.a.fault,.the.pushbutton.commands.are.
executed.one.after.the.other.in.the.sequence.UP.-.STOP.-.UP.
4-channel radio remote control
The.4-channel.radio.remote.control.has.the.following.functions:
Button 1: As with the 1-channel pushbutton switch the pushbutton commands are executed one after the other
in the sequence UP - STOP - DOWN - STOP . If there is a fault, the pushbutton commands are executed
one after the other in the sequence UP - STOP - UP .
Button 2: Operation identical to that of UP button.
Button 3: Operation identical to that of DOWN button. In the event of a fault this button is activated in the dead-
man mode.
Button 4: Operation identical to that of STOP button.
Caution
When using a radio control system the person controlling the door must have a clear view of the door and
its surrounding area during door movement and must not be in a dangerous position.
In setting mode and in the case of a fault, the radio control receiver board has to be removed from slot
J1.
Programming the Hand-held Transmitter Code
The.hand-held.radio.control.transmitter.has.been.coded.by.the.manufacturer..The.radio.control.receiver.must.be.set.to.this.
code..To.program.the.hand-held.transmitter.code.in.the.radio.control.receiver.proceed.as.follows:
•. Press.Program.Channel.1.on.the.radio.control.receiver..The.relevant.red.signal.LED.begins.flashing..You.can.program.the.
hand-held.transmitter.code.within.the.next.15.s.
•. To.do.this.press.the.button.on.the.hand-held.transmitter.for.approx..2.s..The.programming.of.the.hand-held.transmitter.
code.is.confirmed.by.the.signal.LED.on.the.receiver.staying.on.continuously.
•. Now.let.go.of.the.button.on.the.hand-held.transmitter.
You.can.program.the.other.3.buttons.on.the.four-channel.receiver.in.the.same.way..All.in.all.you.can.program.up.to.60.differ-
ent.transmitter.codes.(buttons).for.each.receiver..The.61st.code.will.not.be.accepted.by.the.receiver..In.conjunction.with.the.
1-channel.receiver.you.can.therefore.use.up.to.60.1-channel.hand-held.transmitters.and.in.conjunction.with.the.4-channel.
receiver.you.can.use.up.to.15.4-channel.hand-held.receivers.(if.all.the.buttons.are.used).
36
receiver.board