Schaltplan DCX
Wiring diagram DCX
2
1
Schaltplan DCX 13
Wiring diagram DCX 13
2
1
1. Elektronik
2. Heizelement
3. Sicherheitsdruckbegrenzer SDB
4. Klemmleiste
5. Sicherheitstemperatur begrenzer STB
1. Electronic circuitry
2. Heating element
3. Safety pressure cutout
4. Terminal strip
5. Safety thermal cutout
7. Elektroanschluss
Nur durch den Fachmann!
Zu beachten sind:
• VDE 0100
• EN8062
5
• Bestimmungen der örtlichen
Energie und Wasserversorgungs
unternehmen
3
• Technische Daten und Angaben auf
Typenschild
4
• Gerät an den Schutzleiter
anschließen!
Bauliche Voraussetzungen
• Das Gerät muss dauerhaft an fest ver
legte Leitungen angeschlossen werden.
5
Das Gerät muss an den Schutzleiter
angeschlossen werden.
• Die Elektroleitungen müssen sich in
3
einem einwandfreien Zustand befinden
und dürfen nach der Montage nicht
4
mehr berührbar sein.
• Installationsseitig ist eine allpolige
Trennvorrichtung mit einer Kontakt
öffnungsweite von mindestens 3 mm pro
Pol vorzusehen (z.B. über Sicherungen).
• Zur Absicherung des Gerätes ist ein
Sicherungselement für Leitungsschutz
mit einem dem Gerätenennstrom an ge
passten Auslösestrom zu montieren.
Lastabwurfrelais
Beim Anschluss weiterer Dreh strom geräte
kann ein Last abwurfrelais für elektronische
Durchlauferhitzer (CLAGE Art.Nr. 82250) an
den Außenleiter L
2
Um im niedrigen Leistungsbereich des
Durchlauferhitzers (niedrige Temperatur
und geringer Durchfluss) ein mögliches
Flackern des Lastabwurfrelais zu vermeiden
kann die Betriebsart »Lastabwurfrelais«
aktiviert werden:
• Gerät vom Netz trennen (z.B. durch
Ausschalten der Sicherungen)
• Brücke auf die Leistungselektronik auf
stecken (siehe Bild)
• Gerät wieder in Betrieb nehmen
7. Electrical connection
Only by a specialist!
Please observe:
• The installation must comply with
• The rating plate and technical speci
• The unit must be earthed!
Structural prerequisites
• The appliance must be installed via a
• The electric wiring should not be
• An allpole disconnecting device
• To protect the appliance, a fuse ele
Load shedding relay
If further threephase appliances are con
nected, a load shedding relay designed
for electronic instantaneous water heat
angeschlossen werden.
ers (CLAGE no. 82250) can be connected
to phase conductor L
To avoid possible jitter of the load shed
ding relay caused by low power con
sumption (low temperature set point and
low water flow rate) the "Loadshedding
mode" can be activated as followed:
• Disconnect the appliance from the
• Insert the jumper on the power elect
• Put the appliance into operation again
13
current IEC and national local regula
tions or any particular regulations,
specified by the local electricity sup
ply company
fications
permanent connection. Heater must
be earthed!
injured. After mounting, the wiring
must not be direct accessible.
(e.g. via fuses) with a contact opening
width of at least 3 mm per pole should
be provided at the installation end.
ment must be fitted with a tripping
current commensurate with the
nominal current of the appliance.
.
2
power supply (e.g. by switching of the
fuses)
ronics (see picture)