Maintenance - Stanley FATMAX FMC625 Bedienungsanleitung

ENGLISH (Original instructions)
Assembly
Warning! Before assembly, remove the battery from the tool.
Fitting and removing the battery (fig. B)
To fit the battery (7), line it up with the receptacle on the
u
tool. Slide the battery into the receptacle and push until
the battery snaps into place.
To remove the battery, push the release button (13) while
u
at the same time pulling the battery out of the receptacle.
Fitting and removing a drill bit or screwdriver bit
This tool is fitted with a keyless chuck to allow for an easy
exchange of bits.
Lock the tool by setting the forward/reverse slider (2) to
u
the centre position.
Open the chuck by turning it (4) with one hand while hold-
u
ing the tool with the other.
Insert the bit shaft into the chuck.
u
Firmly tighten the chuck by turning it (4) with one hand
u
while holding the tool with the other.
This tool is supplied with a double-ended screwdriver bit in the
bit holder (6).
To remove the screwdriver bit from the bit holder, lift the bit
u
from the recess.
To store the screwdriver bit, firmly push it into the holder.
u
Use
Warning! Let the tool work at its own pace. Do not overload.
Warning! Before drilling into walls, floors or ceilings, check for
the location of wiring and pipes.
Charging the battery (fig. A)
The battery needs to be charged before first use and whenev-
er it fails to produce sufficient power on jobs that were easily
done before. The battery may become warm while charging;
this is normal and does not indicate a problem.
Warning! Do not charge the battery at ambient temperatures
below 10 °C or above 40 °C. Recommended charging tem-
perature: approx. 24 °C.
Note: The charger will not charge a battery if the cell
temperature is below approximately 0 °C or above 40 °C.
The battery should be left in the charger and the charger
will begin to charge automatically when the cell tempera-
ture warms up or cools down.
To charge the battery (7), insert it into the charger (11).
u
The battery will only fit into the charger in one way. Do
not force. Be sure that the battery is fully seated in the
charger.
Plug in the charger and switch on at the mains.
u
The charging indicator (12) will flash green (slowly).
6
The charge is complete when the charging indicator (12)
lights green continuously. The charger and the battery can be
left connected indefinitely with the LED illuminated. The LED
will change to flashing green (charging) state as the charger
occasionally tops up the battery charge. The charging indica-
tor (12) will be lit as long as the battery is connected to the
plugged-in charger.
Charge discharged batteries within 1 week. Battery life will
u
be greatly diminished if stored in a discharged state.
Leaving the battery in the charger
The charger and battery pack can be left connected with the
LED glowing indefinitely. The charger will keep the battery
pack fresh and fully charged.
Charger diagnostics
If the charger detects a weak or damaged battery, the charg-
ing indicator (12) will flash red at a fast rate. Proceed as
follows:
Re-insert the battery (7).
u
If the charging indicators continues flashing red at a fast
u
rate, use a different battery to determine if the charging
process works properly.
If the replaced battery charges correctly, the original
u
battery is defective and should be returned to a service
centre for recycling.
If the new battery gives the same indication as the original
u
battery, take the charger to be tested at an authorised
services centre.
Note: It may take as long as 60 minutes to determine that
the battery is defective. If the battery is too hot or too
cold, the LED will alternately blink red, fast and slow, one
flash at each speed and repeat.
Selecting the direction of rotation (fig. C)
For drilling and for tightening screws, use forward (clockwise)
rotation. For loosening screws or removing a jammed drill bit,
use reverse (counterclockwise) rotation.
To select forward rotation, push the forward/reverse slider
u
(2) to the left.
To select reverse rotation, push the forward/reverse slider
u
to the right.
To lock the tool, set the forward/reverse slider into the
u
centre position.
Selecting the operating mode or torque (fig. D)
This tool is fitted with a collar to select the operating mode and
to set the torque for tightening screws. Large screws and hard
workpiece materials require a higher torque setting than small
screws and soft workpiece materials. The collar has a wide
range of settings to suit your application.
For drilling in wood, metal and plastics, set the collar (3)
u
to the drilling position by aligning the symbol with the
marking (14).
For screwdriving, set the collar to the desired setting. If
u
you do not yet know the appropriate setting, proceed as
follows:
- Set the collar (3) to the lowest torque setting.
- Tighten the first screw.
- If the clutch ratchets before the desired result is
achieved, increase the collar setting and continue
tightening the screw. Repeat until you reach the correct
setting. Use this setting for the remaining screws.
Drilling in masonry (fig. D & E)
For drilling in masonry, set the collar (3) to the hammer
u
drilling position by aligning the symbol with the marking
(14).
Slide the speed selector (5) towards the front of the tool
u
(2nd gear).
Speed selector (fig. E)
For drilling in steel and for screwdriving applications, slide
u
the speed selector (5) towards the rear of the tool (1st
gear).
For drilling in materials other than steel, slide the speed
u
selector (5) towards the front of the tool (2nd gear).
Drilling/screwdriving
Select forward or reverse rotation using the forward/re-
u
verse slider (2).
To switch the tool on, press the switch (1). The tool speed
u
depends on how far you press the switch.
To switch the tool off, release the switch.
u
LED work light
The LED work light (8) is activated automatically when the trig-
ger is depressed. The LED work light will illuminate when the
trigger is partially depressed, before the unit begins running.
State of charge indicator
The tool is fitted with a state of charge indicator. This can be
used to display the current level of charge in the battery during
use.
Press the state of charge indicator button (9).
u
Hints for optimum use
Drilling
Always apply a light pressure in a straight line with the drill
u
bit.
Just before the drill tip breaks through the other side of the
u
workpiece, decrease pressure on the tool.
(Original instructions) ENGLISH
Use a block of wood to back up workpieces that may
u
splinter.
Use spade bits when drilling large diameter holes in wood.
u
Use HSS drill bits when drilling in metal.
u
Use masonry bits when drilling in soft masonry.
u
Use a lubricant when drilling metals other than cast iron
u
and brass.
Make an indentation using a centre punch at the centre of
u
the hole to be drilled in order to improve accuracy.
Screwdriving
Always use the correct type and size of screwdriver bit.
u
If screws are difficult to tighten, try applying a small
u
amount of washing liquid or soap as a lubricant.
Always hold the tool and screwdriver bit in a straight line
u
with the screw.

Maintenance

Your Stanley Fat Max tool has been designed to operate
over a long period of time with a minimum of maintenance.
Continuous satisfactory operation depends upon proper tool
care and regular cleaning.
Your charger does not require any maintenance apart from
regular cleaning.
Warning! Before performing any maintenance on the tool,
remove the battery from the tool. Unplug the charger before
cleaning it.
Regularly clean the ventilation slots in your tool and
u
charger using a soft brush or dry cloth.
Regularly clean the motor housing using a damp cloth.
u
Do not use any abrasive or solvent-based cleaner.
u
Regularly open the chuck and tap it to remove any dust
u
from the interior.
Z
Protecting the environment
Separate collection. Products and batteries marked
with this symbol must not be disposed of with normal
household waste.
Products and batteries contain materials that can be recov-
ered or recycled reducing the demand for raw materials.
Please recycle electrical products and batteries according to
local provisions. Further information is available at
www.2helpU.com
7