Kärcher SHD-R 3000 Originalbetriebsanleitung Seite 26

Appliance type (see type-
plate)
SHD-R 3000 (F)
SHD-R 3000 (F) S
SHD-R 3000 (F) SVA
SHD-R 3000 (F) SSR
SHD-R 3000 (F) SLA
SHD-R 3000 (F) LM
(F) mobile appliance
* Conditionally resistence, use possible, although Cu and Zn iones in the medium.
Detergent 1 Water with alkaline cleaning agents (max. 0-2%)
Example: Kärcher cleaning agents RM31
2 Water with acid cleaning agents (max. 0-1%)
Example: Kärcher cleaning agents RM25
max. temperature +60 °C (higher temperatures on request, prepressure pump necessary)
Other cleaning liquids can only be used after being released by Kärcher!
 Acids (max. temperature +60 °C):
1)
ATTENTION
– The material will be worn off faster
when using hydrochloric or sulfuric ac-
ids; therefore it must be rinsed/neutral-
ised immediately!
– Contaminated acids will decrease the
resilience!
– Enquire with Kärcher if needed!
– Nitric acid max. 10%.
– Acetic acid max. 10%.
– Formic acid max. 10%.
– Phosphoric acid max. 10%.
– Citric acid max. 10%.
– Sulfuric acid max. 0.5%.
– Hydrochloric acid max. 0.5%.
Brines (max. temperature +60 °C):

2)
1 Caustic soda max. 10%, without hy-
pochlorite particles
2 Potassium hydroxide max. 10%, with-
out hypochlorite particles
 Solvents (max. temperature +60 °C):
3)
1 Hydrocarbons
Example: Petroleum
2 Aromates (solvents)
Example: Benzene, toluene
26
Cleaning liquid
– Water
– Fully desalted water*
– Water with Kärcher detergent
– Water
– Fully desalted water*
– Water with Kärcher detergent
– Water
– Fully desalted water*
– Water with Kärcher detergent
– Water
– Fully desalted water
– Water with Kärcher detergent
– Acids
1)
– Brines
2)
– Water
– Fully desalted water*
– Water with Kärcher detergent
– Brines
2)
– Water
– Fully desalted water*
– Water with Kärcher detergent
– Brines
2)
– Solvent
3)
3 Ketones
Example: MEK (Methyle Ethyle Ke-
tones), Acetone
4 Ester
Example: Butylacetate, Methylacetate
5 Glycoles
Example: Butyl glycole
6 Mixed solvents
Example: Butyl acetate 85, Isobutyl ac-
etate 85 (85 = 85% Butyl acetate + 15%
n-Butanol)
7 Regenerates, distillates from different
solvents, which have already been
used for cleaning purposes or similar
applications.
Cleaning liquids
Working pressure/
pressure setting
safety valve [MPa]
5/6,5
8,5/10
8,5/10
8,5/10
8,5/10
5/6,5
6
-
EN
Remarks
Standard model
Standard model with higher working pres-
sure.
Pump parts that contact the cleaning liq-
uid are made of stainless steel.
– The pistons are made of ceramic ma-
terials. Other pump parts that contact
brines are made of stainless steel.
– Ex model possible.
– Model with higher working pressure.
– Leaking liquid is collected in a pipe
(leakage return).
– Ex model possible.
– Explosion-proof model.
– Leaking liquid is collected in a pipe
(leakage return).
– Additional safety pressure switch (op-
tion).