Herunterladen Inhalt Inhalt Diese Seite drucken

Technical Data; Manufacturer's Terms Of Warranty - Truma Trumatic S 3002 FS Gebrauchsanweisung

Vorschau ausblenden Andere Handbücher für Trumatic S 3002 FS:
Inhaltsverzeichnis

Werbung

Verfügbare Sprachen

Verfügbare Sprachen

Technical data

determined in accordance with EN 624 or
Truma test conditions
Type of gas
Liquid gas (propane / butane)
Operating pressure
30 mbar (see data plate)
Rated thermal output
3400 W
Gas consumption
30 – 280 g/h
Operating voltage
Heater: 1,5 V
Fan:
12 V
Power consumption
Heater: 50 mA (ignition), 0,01 mA (monitoring)
Fan:
0,3 bis 1,0 A
Air flow rate
up to 135 m³/h (with fan duct ÜR dia. 65 mm)
up to 142 m³/h (with fan duct VR dia. 72 mm)
Weight
18,5 kg (with front case and fan )
Declaration of conformity
The liquid gas heater Trumatic S 3002 FS has been approved
by the DVGW and complies with the EC guide lines
(90/396/EWG) for gas appliances as well as with the associ-
ated EC guidelines. The product ID No. for EU countries is
CE-0085AP0325
EC Type Approval
e1 032603
The right to effect technical modifications is reserved!
Dimensions
510 mm
ca. 72 mm
ca. 582 mm
375 mm
280 mm
45 mm
320 mm

Manufacturer's terms of warranty

1. Case of warranty
The manufacturer grants a warranty for malfunctions in the
appliance which are based on material or production faults.
In addition to this, the statutory warranty claims against the
seller remain valid.
A claim under warranty shall not pertain
– for parts subject to wear and in cases of natural wear and
tear,
– as a result of using components in the units that are not
original Truma parts and using unsuitable gas pressure
regulators,
– as a consequence of failure to respect Truma instructions
for installation and use,
– as a consequence of improper handling,
– as a consequence of improper transport packing, not
arranged by Truma.
2. Scope of warranty
The warranty is valid for malfunctions as stated under
item 1, which occur within 24 months after conclusion of
the purchase agreement between the seller and the final
consumer. The manufacturers will make good such defects
by subsequent fulfilment, i.e. at their discretion either by
repair or replacement. In the event of manufacturers provid-
ing service under warranty, the term of the warranty shall not
re commence anew with regard to the repaired or replaced
parts; rather, the old warranty period shall continue to run.
More extensive claims, in particular claims for compensatory
damages by purchasers or third parties, shall be excluded.
This does not affect the rules of the product liability law.
The manufacturer shall bear the cost of employing the Truma
customer service for the removal of a malfunction under war-
ranty – in particular transportation costs, travelling expenses,
job and material costs, as long as the service is carried out in
Germany. The warranty does not cover customer service work
in other countries.
Additional costs based on complicated removal and installa-
tion conditions of the appliance (e.g. removal of furniture or
parts of the vehicle body) do not come under warranty.
3. Raising the case of warranty
The manufacturer's address is:
Truma Gerätetechnik GmbH & Co. KG,
Wernher-von-Braun Strasse 12,
85640 Putzbrunn.
In Germany, always notify the Truma Service Centre if prob-
lems are encountered; in other countries the relevant service
partners should be contacted (see Truma Service Booklet
or www.truma.com). Any complaints are to be described in
detail. In addition, the properly completed guarantee certifi-
cate is to be presented, or the factory number of the unit and
the date of purchase given.
In order for the manufacturers to be able to determine wheth-
er an incident subject to guarantee has occurred, the end user
must, at his own risk, bring the device to the manufacturers or
send it to them. If there is damage to heaters (heat exchang-
ers), the gas pressure regulator must also be sent back to the
factory.
In instances of the device being sent to the works, dispatch
is to be effected by freight transport. In cases under guar-
antee, the works shall bear the transport costs or the costs
of delivery and return. If the damage is deemed not to be a
warranty case, the manufacturer shall notify the customer
and shall specify repair costs which shall not be borne by the
manufacturer; in this case, the customer shall also bear the
shipping costs.
13

Werbung

Inhaltsverzeichnis
loading

Inhaltsverzeichnis