Residual Risks; Technical Data; Operation - Scheppach GS650 Originalbetriebsanleitung

Residual risks

Even if you use this electric power tool in ac-
cordance with instructions, certain residual risks
cannot be rules out. The following hazards may
arise in connection with the equipment's construc-
tion and layout:
• Lung damage if no suitable protective dust mask is
used.
• Damage to hearing if no suitable ear protection is
used.
• Health damage caused by hand-arm vibrations if the
equipment is used over a prolonged period or is not
properly guided and maintained.

Technical Data

Nominal input voltage
Power consumption
Measurement idling speed n
Safety class
Protection category
Weight
Grinding angle range
Sharpness drill diameter
Sharpness knife width
Grinding disc:
Outer diameter
Borehole diameter
* Operating mode S3 - 15% - 10min: S3 = Intermittent
mode without influencing the starting process. This
means that during a period of 10 min the max. operat-
ing time is 15% (1.5 min).
Noise values
The total noise values determined in accordance with
EN 61029.
sound pressure level L
pA
uncertainty K
pA
sound power level L
WA
uncertainty K
WA
Wear hearing protection.
The effects of noise can cause a loss of hearing. Total
vibration values (vector sum - three directions) deter-
mined in accordance with EN 61029.
Assembly
m Caution! Risk of injury!
• Ensure that you have sufficient space in which to
work, and that you do not endanger other people.
• All covers and protective devices must be assembled
properly before commissioning.
• Disconnect the mains plug before changing the
setting on the device.
Setting up
Place the sharpening station on firm surface and fasten
the device. Ideally, bolt the drill to the surface. Use the
mounting holes for the work bench assembly (9) in the
baseplate for this.
The screws and nuts required for assembly are not part
of the scope of delivery.
 www.scheppach.com  service@scheppach.com  +(49)-08223-4002-99  +(49)-08223-4002-58  www.scheppach.com  service@scheppach.com  +(49)-08223-4002-99  +(49)-08223-4002-58
230V~ 50Hz
65W (S3 15%)*
6700 min
-1
0
II
IP20
1.5 kg
20° - 40°
3 - 10mm
6 - 51mm
max. 48mm
10mm
74 dB(A)
3 dB
87 dB(A)
3 dB
Mount the sharpener
1. Select one of the three sharpeners.
2. In order to remove a sharpener from the working
position, you must press down the release lever for
the sharpener (13).
3. Remove the sharpener from the guide rails, upwards.
4. In the storage positions, the sharpeners are not fixed
to the right and left side and can be easily removed
from the guide rails.
5. In order to fasten the selected sharpener in the
working position, from above push this into the guide
rails. Press the sharpener down until it snaps into
place.
The sharpeners also present a safety device. Never
use this device without a sharpener. Risk of injury!

Operation

m Caution! Risk of injury!
• Always disconnect the plug from the mains socket
before working.
• Use only grinding disks and accessories
recommended by the manufacturer. The use of other
insertion tools and other accessories may cause risk
of injury.
• Never operate the device without the visual protection
disk.
• Switch on the equipment only when it is safely
installed on the work surface.
Despite spark protection, always wear safety
goggles while working in order to avoid eye injuries.
Keep your hands away from the grinding disc and
grinding belt when the device is in operation. Injury
hazard!
Switching on and off
Ensure that the mains voltage matches the
specifications on the rating plate.
Connect the equipment to the mains.
1. To switch on, press the "I" On switch and the device
starts up (see 3).
2. To switch off, press the "0" off switch and the device
switches off (see 3).
After switching on the device, wait until the device has
reached its max. speed. Only then must you start with
the grinding.
m The disk will continue to run after the equipment is
switched off. There is a risk of injury.
Test run:
Before starting work and after each change of grinding
disk, carry out a test run of at least 60 seconds with no
load. Switch off the equipment immediately if the disk
runs lumpy, substantial vibrations occur, or abnormal
noises are generated.
Sharpening drills (Fig. B)
Drills with a diameter of 3-10 mm can be sharpened.
1. Mount the selected sharpener (see Mounting
sharpener).
2. Remove the drill holder (14) from the sharpener.
17 І 80