Kärcher CB 1/23 Eco Bedienungsanleitung Seite 33

54 Travel command has been given but
SB1A (side brush 1, outward) limit switch
has not been exited
55 Limit switch SB1A (side brush 1, outward)
has not reached expected position
56 Travel command has been given but
SB1E (side brush 1, driven-in) limit switch
has not been exited
57 Limit switch SB1E (side brush 1, driven-in)
has not reached expected position
58 Travel command has been given but
SB2A (side brush 2, outward) limit switch
has not been exited
59 Limit switch SB2A (side brush 2, outward)
has not reached expected position
60 Travel command has been given but
SB2E (side brush 2, driven-in) limit switch
has not been exited
61 Limit switch SB2E (side brush 2, driven-in)
has not reached expected position
62 Travel command has been given but DBO
(top roof brush) limit switch has not been
exited
63 Limit switch DBO (top roof brush) has not
reached expected position
66 Travel command has been given but DBU
limit switch (lower roof brush) has not
been exited
67 Limit switch DBU (lower roof brush) has
not reached expected position
68 Travel command has been given but TRO
(upper roof drier) limit switch has not been
exited
69 Limit switch TRO (upper roof drier) has not
reached expected position
70 Travel command has been given but TRU
(lower roof drier) limit switch has not been
exited
71 Limit switch TRU (lower roof drier) has not
reached expected position
80 Roof brush alignment too high
81 Roof brush alignment too low
83 Roof brush performance during the wash
too low
84 Side-brush 1 alignment too high
85 Side-brush 1 alignment too low
87 Side-brush 1 performance during the
wash too low
88 Side-brush 2 alignment too high
89 Side-brush 2 alignment too low
91 Side-brush 2 performance during the
wash too low
100 Wheel wash 1 does not drive back to base
setting
101 Wheel wash 2 does not drive back to base
setting
102 Roof brush limit 4 too long exceeded
103 Side brush 1 limit 4 too long exceeded
104 Side brush 2 limit 4 too long exceeded
105 Washing section takes too long
106 Maximum idling time of portal exceeded
Limit switch activated through foreign met-
al or is defective, drive wheel is turning
Limit switch defective, drive wheel is turning
Limit switch is defective
Cable, motor or gears of rotary roof brush-
es defective
Cable, motor or gears of rotary side brush
1 defective
Cable, motor or gears of rotary side brush
2 defective
No compressed air, wheel wash has got
jammed in the rim
Cable, motor or gear of rotation roof brush
defective or vehicle of this type cannot be
washed
Cable, motor or gear of rotation side-brush
1 defective or vehicle of this type cannot
be washed
Cable, motor or gear of rotation side-brush
2 defective or vehicle of this type cannot
be washed
Washing unit does not move during washing Switch off and switch on the unit, repeat
14
-
EN
Check limit switch of side brushes for de-
fects; clean upper running surface of the
side-brush holder; switch off/on the unit,
repeat washing process
Check limit switch for damages, switch on/
off the unit, repeat washing process
Switch off and switch on the unit, repeat
washing process, call Customer Service
Check compressed air supply and com-
pressor; switch off the unit and remove the
wheel wash from the rim; repeat washing
process
Drive vehicle out of the plant, switch off
main switch, wait for 10 seconds, switch on
main switch again, press Reset button,
press button Normal setting, repeat wash-
ing procedure.
washing process, call Customer Service
33