Assembly - Powerfix Z15003 Bedienungsanleitung

Assembly

CAUTIOn! DAngEr OF FIrE! Assemble
and use the product on a fire-resistant surface only.
The following tools are required for
assembly:
7 x Open spanners (1 x 8 mm, 2 x 10 mm,
2 x 14 mm, and possibly 2 x 17 mm)
2 x Allen key
1 x Slotted head screwdriver (approx. 5 mm)
Follow these steps:
Fasten the saddle
33
with the hexagonal socket head screws
and washers (see Fig. A).
34
Fasten the handle
the projecting screw thread and the corresponding
nut (see Fig. A).
note: Please bear in mind that the angle
grinder must be fitted with a suitable cutting
disc before assembly. It is not possible to
change the disc with the angle grinder installed
in the stand.
Now mount the angle grinder in the mount
note: At this point, first check the size of the
handle thread of your angle grinder. It may be
M6, M8 or M10.
Then place the corresponding mounting bolts
, , washers
10 11 8
, distance pieces
14
bushings , to one side, ready for use.
6 7
Insert the necessary plastic bushings
into the mounting pieces
note: Ensure that the size of the plastic
bushings , matches the required
6 7
mounting bolts ,
9
required for mounting bolts M10
Screw the matching mounting bolt
through the rear mounting piece
Fasten the rear mounting piece
tightening the corresponding size of nut
on the mounting bolt
14
turning it in the direction of the mounting piece
(see Fig. B).
Insert the adjustment screw
bottom hole and the adjustment screw
on to the base plate
35
on to the mount with
3 36
and matching nuts ,
12
, , and plastic
15 16 17
,
6 7
, (see Fig. B).
18 38
. Plastic bushings are not
10
.
11
, ,
9 10
(see Fig. B).
38
in place by
38
,
12
, , (i.e. by
9 10 11
through the
20
1
through the top hole of the mount
that later the rubber buffers of these screws
must lie against the angle grinder housing.
note: First insert these screws so that the rubber
buffers lie directly against the mount
Now push the plastic locating pieces
mounting pieces
mount (Figure B).
36
Then attach the mounting pieces
through the plastic locating pieces
hexagonal socket head screws
elongated holes in the mount
Place the desired distance piece
32
the mounting bolt
on to the front mounting piece
note: The three distance pieces
are of different lengths. Choose the distance
piece ,
15 16
note: Set the distance piece
that the cutting disc cannot come into contact
with the workbench / table below the base
plate (see Figure E).
32
Screw the matching mounting bolt
. through the front mounting piece
36
Fasten the front mounting piece
tightening the corresponding size of nut
on the mounting bolt
14
, turning it in the direction of the mounting piece
9
, Now set the adjustment screws
13
the angle grinder is aligned at right angles to
the base plate
mount .
36
After slightly loosening the hexagonal socket
head screws
the cutting disc of the angle grinder lowers into
centre of the slot provided in the base plate
Now attach the safety guard
push the safety guard
11
and fasten it in place with the nut
Now insert the metal rod
, corresponding opening in the mount
13
fasten it in place with the nut
) mounting bolt
38
Always keep the angle grinder's mains lead in
place using the clip
After assembly is complete, switch the angle
36
, on to the guide of the
18 38
,
18
19
in the
31
(see Fig. A).
36
,
15
, , and washer
9 10 11
(see Fig. D).
18
15
, of the most appropriate length.
17
,
15 16
9
18
in place by
18
, ,
9 10 11
,
1 20
and firmly attached to the
32
, adjust the saddle
35 33
. To do this
5
on to the metal rod
5
(see Fig. C).
4
into the
2
and the
39
(see Fig. C).
40
.
37
. Note
.
36
of the
19
38
with the
, on
16 17
8
, ,
16 17
, so
17
, ,
10 11
.
, ,
12 13
(i.e. by
).
18
so that
so that
.
32
2
and
36
GB/IE 7