Specifications - Makita 3612C Bedienungsanleitung

ENGLISH (Original instructions)
1-1. Stopper pole
1-2. Fast-feed button
1-3. Adjusting hex bolt
1-4. Stopper block
2-1. Knob
3-1. Nylon nut
3-2. Stopper pole
3-3. Fast-feed button
3-4. Adjusting hex bolt
3-5. Stopper block
3-6. Lock lever
4-1. Stopper pole
4-2. Hex bolt
4-3. Hex nut
4-4. Stopper block
5-1. Switch lever
6-1. Lock-off button
6-2. Switch trigger
7-1. Speed adjusting dial
8-1. Wrench
8-2. Shaft lock
8-3. Lock lever
9-1. Chip deflector
10-1. Feed direction
10-2. Bit revolving direction

SPECIFICATIONS

Collet chuck capacity
Plunge capacity
No load speed (min
• Due to our continuing programme of research and development, the specifications herein are subject to change without notice.
• Specifications may differ from country to country.
• Weight according to EPTA-Procedure 01/2003
Intended use
The tool is intended for flush trimming and profiling of
wood, plastic and similar materials.
Power supply
The tool should be connected only to a power supply of
the same voltage as indicated on the nameplate, and can
only be operated on single-phase AC supply. They are
double-insulated and can, therefore, also be used from
sockets without earth wire.
Explanation of general view
10-3. Workpiece
10-4. Straight guide
12-1. Wing bolt (A)
12-2. Guide holder
12-3. Fine adjusting screw
12-4. Wing bolt (B)
12-5. Straight guide
13-1. More than 15mm (5/8")
13-2. Straight guide
13-3. Wood
15-1. Templet guide
15-2. Screw
15-3. Base plate
16-1. Templet guide
16-2. Lock plate lever
17-1. Bit
17-2. Base
17-3. Templet
17-4. Workpiece
17-5. Distance (X)
17-6. Outside diameter of the templet
17-7. Templet guide
19-1. Wing bolt (A)
19-2. Guide holder
Model
-1
)
Overall length
Base diameter
Net weight
Safety class
guide
ENE010-1
For public low-voltage distribution systems of
between 220 V and 250 V.
Switching operations of electric apparatus cause voltage
ENF002-2
fluctuations. The operation of this device under
unfavorable mains conditions can have adverse effects
to the operation of other equipment. With a mains
impedance equal or less than 0.32 Ohms it can be
presumed that there will be no negative effects. The
mains socket used for this device must be protected with
a fuse or protective circuit breaker having slow tripping
characteristics.
6
19-3. Fine adjusting screw
19-4. Wing bolt (B)
19-5. Wing bolt (C)
19-6. Trimmer guide
19-7. Guide roller
20-1. Bit
20-2. Guide roller
20-3. Workpiece
21-1. Pan head screw
21-2. Dust cover
22-1. Collet nut
22-2. Collet cone
22-3. Spacer
23-1. Vacuum head
24-1. Vacuum head
24-2. Screws
25-1. Vacuum head
26-1. Support
26-2. Lock lever
28-1. Limit mark
29-1. Brush holder cap
29-2. Knob
29-3. Screwdriver
3612
12 mm or 1/2"
0 - 60 mm
22,000
297 mm (324 mm with knob)
160 mm
5.7 kg
/II
3612C
9,000 - 23,000
5.8 kg
ENF100-1