Functional Description - Makita 3612C Bedienungsanleitung

5. Check the bit carefully for cracks or damage
before operation.
damaged bit immediately.
6. Avoid cutting nails. Inspect for and remove all
nails from the workpiece before operation.
7. Hold the tool firmly with both hands.
8. Keep hands away from rotating parts.
9. Make sure the bit is not contacting the
workpiece before the switch is turned on.
10. Before using the tool on an actual workpiece,
let it run for a while. Watch for vibration or
wobbling that could
installed bit.
11. Be careful of the bit rotating direction and the
feed direction.
12. Do not leave the tool running. Operate the tool
only when hand-held.
13. Always switch off and wait for the bit to come
to a complete stop before removing the tool
from workpiece.
14. Do not touch the bit immediately after
operation; it may be extremely hot and could
burn your skin.
15. Do not smear the tool base carelessly with
thinner, gasoline, oil or the like. They may
cause cracks in the tool base.
16. Draw attention to the need to use cutters of
the correct shank diameter and which are
suitable for the speed of the tool.
17. Some material contains chemicals which may
be toxic. Take caution to prevent dust
inhalation and skin contact. Follow material
supplier safety data.
18. Always use the correct dust mask/respirator
for the material and application you are
working with.
SAVE THESE INSTRUCTIONS.
WARNING:
DO NOT let comfort or familiarity with product
(gained from repeated use) replace strict adherence
to safety rules for the subject product. MISUSE or
failure to follow the safety rules stated in this
instruction manual may cause serious personal
injury.
Replace cracked
indicate improperly

FUNCTIONAL DESCRIPTION

or
CAUTION:
Always be sure that the tool is switched off and
•
unplugged before adjusting or checking function on
the tool.
Adjusting the depth of cut
Fig.1
Place the tool on a flat surface. Loosen the lock lever and
lower the tool body until the bit just touches the flat
surface. Press the lock lever down to lock the tool body.
Now lower the stopper pole until it makes contact with the
adjusting hex bolt. The stopper pole can be moved
rapidly by depressing the fast-feed button. While
pressing the fast-feed button, raise the stopper pole until
the desired depth of cut is obtained. The depth of cut is
equal to the distance between the stopper pole and the
adjusting hex bolt. Stopper pole travel can be checked
with the scale (1 mm per graduation) on the tool body.
Minute depth adjustments can be obtained by turning the
stopper pole (1.5 mm per turn).
Now, your predetermined depth of cut can be obtained by
loosening the lock lever and then lowering the tool body
until the stopper pole makes contact with the adjusting
hex bolt.
CAUTION:
Since excessive cutting may cause overload of the
•
motor or difficulty in controlling the tool, the depth of
cut should not be more than 20 mm at a pass when
cutting grooves. When you wish to cut grooves
more than 20 mm deep, make several passes with
progressively deeper bit settings.
Do not lower the knob too low. The bit will protrude
•
dangerously.
For the tool with knob
Fig.2
By turning the knob, the upper limit of the tool body can
be adjusted. When the tip of the bit is retracted more than
required in relation to the base plate surface, turn the
knob to lower the upper limit.
For the tool with nylon nut
Fig.3
The upper limit of the tool body can be adjusted by
turning the nylon nut. Do not lower the nylon nut too low.
The bit will protrude dangerously.
Stopper block
Fig.4
The stopper block has three adjusting hex bolts which
raise or lower 0.8 mm per turn. You can easily obtain
three different depths of cut using these adjusting hex
bolts without readjusting the stopper pole.
Adjust the lowest hex bolt to obtain the deepest depth of
cut, following the method of "Adjusting depth of cut".
8