Specifications; Specific Safety Rules - Makita 3612 Betriebsanleitung

ENGLISH
1 Wrench
2 Router bit
3 Shaft lock
4 Tighten
5 Loosen
6 Nylon nut
7 Stopper pole
8 Fast-feed button
9 Lock lever
10 Adjusting hex bolt
11 Stopper
12 Stopper pole
13 Chip deflector
14 Adjusting hex bolt
15 Hex nut
16 Stopper
17 Switch lever
18 Lock-off button
19 Switch trigger
20 Speed change knob

SPECIFICATIONS

Model
Collet capacity .............................................................................12 mm or 1/2"
Plunge capacity ...........................................................................0 – 60 mm
–1
No load speed (min ) .................................................................22,000
Overall heigth ..............................................................................297 mm
Base diameter .............................................................................160 mm
Net weight ....................................................................................5.8 kg
• Due to our continuing program of research and devel-
opment, the specifications herein are subject to change
without notice.
• Note: Specifications may differ from country to country.
Power supply
The tool should be connected only to a power supply of
the same voltage as indicated on the nameplate, and can
only be operated on single-phase AC supply. They are
double-insulated in accordance with European Standard
and can, therefore, also be used from sockets without
earth wire.
For public low-voltage distribution systems of
between 220 V and 250 V
Switching operations of electric apparatus cause voltage
fluctuations. The operation of this device under unfavor-
able mains conditions can have adverse effects to the
operation of other equipment. With a mains impedance
equal or less than 0.32 Ohms it can be presumed that
there will be no negative effects.
The mains socket used for this device must be protected
with a fuse or protective circuit breaker having slow trip-
ping characteristics.
Safety hints
For your own safety, please refer to the enclosed safety
instructions.
Explanation of general view
21 Workpiece
22 Bit revolving direction
23 Feed direction
24 View from the top of the tool
25 Correct bit feed direction
26 Straight guide
27 Guide holder
28 Fine adjusting screw
29 Wing bolt (B)
30 Wing bolt (A)
31 Stright guide
32 More than 15 mm
33 Straight guide
34 Wood
35 Trimmer guide
36 Wing bolt (A)
37 Guide roller
38 Guide holder
39 Fine adjusting screw
40 Wing bolt (B)

SPECIFIC SAFETY RULES

DO NOT let comfort or familiarity with product
(gained from repeated use) replace strict adherence
to router safety rules. If you use this tool unsafely or
incorrectly, you can suffer serious personal injury.
1.
2.
3.
4.
5.
6.
7.
8.
9.
41 Wing bolt (C)
42 Trimmer guide
43 Templet guide
44 Screw
45 Templet guide
46 Lock plate lever
47 Bit
48 Base
49 Templet
50 Workpiece
51 Templet guide
52 Vaccum head
53 Screws
54 Support
55 Lock lever
56 Limit mark
57 Brush holder cap
58 Screwdriver
3612
Hold power tool by insulated gripping surfaces
when performing an operation where the cutting
tool may contact hidden wiring or its own cord.
Contact with a "live" wire will make exposed
metal parts of the tool "live" and shock the oper-
ator.
Use clamps or another practical way to secure
and support the workpiece to a stable platform.
Holding the work by hand or against your body
leaves it unstable and may lead to loss of con-
trol.
Wear hearing protection during extended period
of operation.
Handle the bits very carefully.
Check the bit carefully for cracks or damage
before operation.
Replace cracked or damaged bit immediately.
Avoid cutting nails. Inspect for and remove all
nails from the workpiece before operation.
Hold the tool firmly.
Keep hands away from rotating parts.
Make sure the bit is not contacting the work-
piece before the switch is turned on.
3612C
12 mm or 1/2"
0 – 60 mm
9,000 – 23,000
297 mm
160 mm
6.0 kg
GEB018-1
5