Specifications; Intended Use; Power Supply - Makita RP1802 Betriebsanleitung

ENGLISH (Original instructions)

SPECIFICATIONS

Model:
Collet chuck capacity
Plunge capacity
No load speed
Overall height
Net weight
Safety class
Lamp
Speed adjusting dial
Electric brake
• Due to our continuing program of research and development, the specifications herein are subject to change without notice.
• Specifications may differ from country to country.
• Weight according to EPTA-Procedure 01/2014

Intended use

The tool is intended for flush trimming and profiling of
wood, plastic and similar materials.

Power supply

The tool should be connected only to a power supply of the same
voltage as indicated on the nameplate, and can only be operated
on single-phase AC supply. They are double-insulated and can,
therefore, also be used from sockets without earth wire.
Noise
The typical A-weighted noise level determined accord-
ing to EN62841-2-17:
Model RP1802
Sound pressure level (L
Sound power level (L ) : 96 dB (A)
WA
Uncertainty (K) : 3 dB(A)
Model RP1802F
Sound pressure level (L
Sound power level (L ) : 96 dB (A)
WA
Uncertainty (K) : 3 dB(A)
Model RP1803
Sound pressure level (L
Sound power level (L ) : 96 dB (A)
WA
Uncertainty (K) : 3 dB(A)
Model RP1803F
Sound pressure level (L
Sound power level (L ) : 96 dB (A)
WA
Uncertainty (K) : 3 dB(A)
Model RP2302FC
Sound pressure level (L
Sound power level (L ) : 99 dB (A)
WA
Uncertainty (K) : 3 dB(A)
Model RP2303FC
Sound pressure level (L
Sound power level (L ) : 99 dB (A)
WA
Uncertainty (K) : 3 dB(A)
) : 85 dB(A)
pA
) : 85 dB(A)
pA
) : 85 dB(A)
pA
) : 85 dB(A)
pA
) : 88 dB(A)
pA
) : 88 dB(A)
pA
RP1802 RP1802F RP1803
-1
23,000 min
312 mm
-
-
-
NOTE: The declared noise emission value(s) has been
measured in accordance with a standard test method
and may be used for comparing one tool with another.
NOTE: The declared noise emission value(s) may
also be used in a preliminary assessment of exposure.
WARNING:
Wear ear protection.
WARNING:
The noise emission during actual
use of the power tool can differ from the declared
value(s) depending on the ways in which the tool is
used especially what kind of workpiece is processed.
WARNING:
Be sure to identify safety measures
to protect the operator that are based on an estima-
tion of exposure in the actual conditions of use (tak-
ing account of all parts of the operating cycle such
as the times when the tool is switched off and when
it is running idle in addition to the trigger time).
NOTE: The declared noise emission value(s) has been
measured in accordance with a standard test method
and may be used for comparing one tool with another.
NOTE: The declared noise emission value(s) may
also be used in a preliminary assessment of exposure.
WARNING:
Wear ear protection.
WARNING:
The noise emission during actual
use of the power tool can differ from the declared
value(s) depending on the ways in which the
tool is used especially what kind of workpiece is
processed.
WARNING:
Be sure to identify safety mea-
sures to protect the operator that are based on an
estimation of exposure in the actual conditions of
use (taking account of all parts of the operating
cycle such as the times when the tool is switched
off and when it is running idle in addition to the
trigger time).
9 ENGLISH
RP1803F RP2302FC RP2303FC
12 mm or 1/2"
0 - 70 mm
-1
22,000 min 9,000 - 23,000 min
327 mm
6.2 kg
/II
-
-
-1