Specifications - Makita RP0910 Bedienungsanleitung

ENGLISH (Original instructions)
1-1. Adjusting knob
1-2. Stopper pole
1-3. Depth pointer
1-4. Stopper pole setting nut
1-5. Lock knob
1-6. Fast-feed button
1-7. Adjusting hex bolt
1-8. Stopper block
2-1. Nylon nut
3-1. Stopper pole
3-2. Adjusting hex bolt
3-3. Stopper block
4-1. Lock button
4-2. Switch trigger
5-1. Speed adjusting dial

SPECIFICATIONS

Collet chuck capacity
Plunge capacity
No load speed (min
• Due to our continuing program of research and development, the specifications herein are subject to change without notice.
• Specifications may differ from country to country.
• Weight according to EPTA-Procedure 01/2003
Intended use
The tool is intended for flush trimming and profiling of
wood, plastic and similar materials.
Power supply
The tool should be connected only to a power supply of
the same voltage as indicated on the nameplate, and
can only be operated on single-phase AC supply. They
are double-insulated and can, therefore, also be used
from sockets without earth wire.
Noise
The typical A-weighted noise level determined according
to EN60745:
Model RP0910
Sound pressure level (L
Sound power level (L
Uncertainty (K) : 3 dB (A)
Model RP1110C
Sound pressure level (L
Sound power level (L
Uncertainty (K) : 3 dB (A)
Explanation of general view
6-1. Collet nut
6-2. Tighten
6-3. Loosen
6-4. Wrench
6-5. Shaft lock
7-1. Correct size collet cone
8-1. Feed direction
8-2. Bit revolving direction
8-3. Workpiece
8-4. Straight guide
10-1. Lock screw
10-2. Guiding surface
10-3. Straight guide
13-1. Screw
13-2. Templet guide
Model
-1
)
Overall height
Net weight
Safety class
) : 83 dB (A)
pA
) : 94 dB (A)
WA
) : 81 dB (A)
pA
) : 92 dB (A)
WA
RP0910
8 mm or 1/4"
0 - 57 mm
27,000
260 mm
3.3 kg
ENE010-1
Vibration
ENF002-2
The vibration
determined according to EN60745:
Model RP0910
Work mode : cuttig grooves in MDF
Vibration emission (a
ENG905-1
Uncertainty (K) : 1.5 m/s
Model RP1110C
Work mode : cuttig grooves in MDF
Vibration emission (a
Uncertainty (K) : 1.5 m/s
The declared vibration emission value has been
•
measured in accordance with the standard test
method and may be used for comparing one tool
with another.
The declared vibration emission value may also be
•
used in a preliminary assessment of exposure.
5
14-1. Bit
14-2. Base
14-3. Templet
14-4. Workpiece
14-5. Distance (X)
14-6. Outside diameter of the templet
guide
14-7. Templet guide
15-1. Dust nozzle assembly
15-2. Nozzle assembly
16-1. Limit mark
17-1. Brush holder cap
17-2. Screwdriver
/II
Wear ear protection
total value (tri-axial
) : 8.0 m/s
h
2
) : 5.0 m/s
h
2
RP1110C
8 mm or 1/4"
0 - 57 mm
8,000 - 24,000
260 mm
3.4 kg
/II
ENG900-1
vector sum)
2
2
ENG901-1