Specifications; General Safety Rules - Makita RP0910 Betriebsanleitung

ENGLISH
1 Collet nut
2 Wrench
3 Shaft lock
4 Tighten
5 Loosen
6 Correct size collet cone
7 Stopper pole
8 Depth pointer
9 Lock knob
10 Fast-feed button
11 Adjusting hex bolt
12 Adjusting knob
13 Stopper block
14 Nylon nut

SPECIFICATIONS

Model
Max. collet capacity ..................................................................... ø8 mm
Plunge capacity ........................................................................... 0 – 57 mm
–1
No load speed (min ) ................................................................. 27,000
Overall height .............................................................................. 260 mm
Net weight ................................................................................... 3.3 kg
• Due to our continuing program of research and devel-
opment, the specifications herein are subject to change
without notice.
• Note: Specifications may differ from country to country.
Power supply
The tool should be connected only to a power supply of
the same voltage as indicated on the nameplate, and can
only be operated on single-phase AC supply. They are
double-insulated in accordance with European Standard
and can, therefore, also be used from sockets without
earth wire.

GENERAL SAFETY RULES

WARNING! Read all instructions. Failure to follow all
instructions listed below may result in electric shock, fire
and/or serious injury. The term "power tool" in all of the
warnings listed below refers to your mains-operated
(corded) power tool or battery-operated (cordless) power
tool.
SAVE THESE INSTRUCTIONS.
Work area safety
1. Keep work area clean and well lit. Cluttered and
dark areas invite accidents.
2. Do not operate power tools in explosive atmo-
spheres, such as in the presence of flammable
liquids, gases or dust. Power tools create sparks
which may ignite the dust or fumes.
3. Keep children and bystanders away while oper-
ating a power tool. Distractions can cause you to
lose control.
Electrical safety
4. Power tool plugs must match the outlet. Never
modify the plug in any way. Do not use any
adapter plugs with earthed (grounded) power
tools. Unmodified plugs and matching outlets will
reduce risk of electric shock.
6
Explanation of general view
15 Hex nut
16 Lock button
17 Switch trigger
18 Speed adjusting dial
19 Workpiece
20 Bit revolving direction
21 Feed direction
22 (View from the top of the
tool)
23 Correct bit feed direction
24 Lock screw
25 Guiding surface
26 Straight guide
27 Templet guide
5.
6.
7.
8.
GEA001-3
Personal safety
9.
10. Use safety equipment. Always wear eye protec-
11. Avoid accidental starting. Ensure the switch is in
12. Remove any adjusting key or wrench before
28 Screw
29 Bit
30 Base
31 Templet
32 Workpiece
33 Templet guide
34 Nozzle assembly
35 Dust nozzle assembly
36 Limit mark
37 Brush holder cap
38 Screwdriver
39 Stopper pole setting nut
RP0910
Avoid body contact with earthed or grounded
surfaces such as pipes, radiators, ranges and
refrigerators. There is an increased risk of electric
shock if your body is earthed or grounded.
Do not expose power tools to rain or wet condi-
tions. Water entering a power tool will increase the
risk of electric shock.
Do not abuse the cord. Never use the cord for
carrying, pulling or unplugging the power tool.
Keep cord away from heat, oil, sharp edges or
moving parts. Damaged or entangled cords
increase the risk of electric shock.
When operating a power tool outdoors, use an
extension cord suitable for outdoor use. Use of a
cord suitable for outdoor use reduces the risk of
electric shock.
Stay alert, watch what you are doing and use
common sense when operating a power tool. Do
not use a power tool while you are tired or under
the influence of drugs, alcohol or medication. A
moment of inattention while operating power tools
may result in serious personal injury.
tion. Safety equipment such as dust mask, non-skid
safety shoes, hard hat, or hearing protection used
for appropriate conditions will reduce personal inju-
ries.
the off-position before plugging in. Carrying
power tools with your finger on the switch or plug-
ging in power tools that have the switch on invites
accidents.
turning the power tool on. A wrench or a key left
attached to a rotating part of the power tool may
result in personal injury.
RP1110C
ø8 mm
0 – 57 mm
8,000 – 24,000
260 mm
3.4 kg