Inhaltsverzeichnis
Werbung
Verfügbare Sprachen
Verfügbare Sprachen
8.7 Switching the device on / off via remote control
• Ensure that the power switch on the backside of the Medow ring light 960 is <ON>. The <ON/
OFF> function on the remote control will not work if the power switch on the ring light is swit-
ched off.
• P ress the ON/OFF switch on the remote control once briefly to activate the display. The cur-
rently selected settings will be shown on the display of the device and the remote control.
• Ensure that the device and the remote control have been correctly connected and set the
same channels and groups. (See previous section 8.6).
• B y briefly pressing the <ON/OFF> switch on the remote control, you can switch the lamp on
and off, or set it to the standby mode. (Note that the lamp will not shine on when the brightness
is set to zero.
• The display of the remote control has an automatic switch off function. To reactivate the dis-
play, please press the <SET> button briefly.
8.8 Setting brightness (dimmer function) on the remote control
• Press the ON/OFF switch or the <SET> button on the remote control once to active the display
of the remote control.
• Ensure that the device and the remote control have been correctly connected and set the
same channels and groups. (See previous section 8.6).
• Select the brightness setting. Usually, after pressing the ON/OFF switch, the dim function is
activated.
• You can see the currently selected value as a percentage on the display of the remote control
and on the ring lamp. When selecting the brightness setting, the corresponding field in the
display of the lamp and remote control will NOT flash (like for example, when setting the colour
temperature).
• Press the plus <+> or minus <-> buttons on the remote control to increase or reduce the light
intensity.
• The brightness can be adjusted in steps of 1 % from 0 to 100 %.
• The brightness of the ring light changes and the selected values for the brightness are shown
on the displays of the lamp and the remote control at the same time.
• The selected values are set and saved by the device immediately.
8.9 Setting the colour temperature via the remote control
• P ress the ON/OFF switch or the <SET> button on the remote control once briefly if the display
is not activated.
• Ensure that the device and the remote control have been correctly paired up and set to the
same channels and groups. (See previous section 8.6).
• B y pressing the <SET> button on the remote control briefly, you can switch between setting the
brightness and the colour temperature.
• Select the colour temperature setting. If the display for the value of the colour temperature
flashes, the colour temperature has been activated.
• Press the plus <+> or minus <-> buttons on the remote control to increase or reduce the colour
temperature.
• The colour temperature of the light emitted by the device changes and the selected values
for the colour temperature are changed and shown on the display of the lamp and the remote
control at the same time.
• The colour temperature can be set in steps of 10 Kelvin from 3,200 to 5,500 Kelvin.
• The selected values are set by the device immediately.
• Save the desired value for the colour temperature by pressing the <SET> button briefly.
36
8.10 General notes to the channel and group selection
It is possible to control groups of lights in addition to operating them on multiple channels. For
instance, you can set one or more lights to Group A and other sets of lights to Group B, Group
C through Group F (6 Groups). You can then control all lights in the same group simultaneously
if they are all on the same channel 1-50. Individual lights in the same group can also be adjus-
ted independently within the same group if they are set to different channels.
To set the group number for a particular light, press the controller knob in and hold for 3-5
seconds. When the Group selector begins to flash, remove your finger. Before the third flash,
turn the Group selector counterclockwise to select a lower group or clockwise to select a higher
group. When the controller knob is pressed in and held, it will alternate between the Group
Selector and the Channel Selector. Remove you finger while the desired selector is flashing.
9.
Transporting, storing the device
WARNING
Danger of fire caused by hot parts of the equipment. Allow the device to cool down completely.
• Switch off the device (See „Switching the device on, off).
• Allow the device to cool down completely.
• Unplug the power supply cable from the device.
• If necessary clean the device (See „Cleaning the device").
• Lay the device and all disassembled elements into the original article packaging box and
transport of store as specified in the technical specifications. See technical specifications.
37
Werbung
Inhaltsverzeichnis
