Operating The Device, Settings And Display Signals; Switching The Device On/Off; Setting Brightness; Setting The Colour Temperature On The Device - Walimex Pro Medow 960 Pro Bi Color Bedienungsanleitung

CAUTION
■ Do not short circuit.
■ Do not expose to rain or immerse in water. This battery is not water proof.
■ Keep out of reach of children.
■ Do not continuously charge for more then 24 hours.
■ Store in dry, cool, ventilated place.
■ Do not place into fire or expose to extreme heat.
■ Dead batteries should be disposed according to local regulations.
■ If the battery has not been used for over 3 months, please make a full recharge.
■ Do not use the led light while loading the battery.
WARNING
Precautions when using with rechargeable battery
These can run out or explode, if inappropriately handled. Please observe the following safety
notes when handling the rechargeable battery for use with this unit:
■ Use only rechargeable batteries mentioned in these operating instructions.
■ Do not lay the rechargeable battery into fire or expose these to direct heat.
■ To prevent the product from being damaged make sure you have removed the rechargeable
battery if you will not use the product over a longer period of time or if the rechargeable battery
has been discharged.
■ If battery fluid has come into contact with skin or clothes, flush it off immediately with fresh water.
■ Do not recharge the rechargeable battery unattended.
■ Once the reacharging process is finished, disconnect the charger from the power supply.
Recommendations for using your battery
• C hange the battery, at the latest, when the light starts to flicker
• Switch the device off before removing the battery.
• This also applies for changing or adding another battery in models with several battery
mounts. Switch the light off before adding or changing the battery, and do not insert other
batteries into the mount while the light is being used.
• Do not let the battery charge level go too low, and charge up your battery as soon as pos-
sible. This ensures the longer battery life.
• Please remove the battery from the battery mount while transporting or storing the device.
This is to prevent damage to the battery mounts during transportation and prevents the
battery becoming uncharged unintentionally.
• To maintain the performance of your battery, we recommend letting the battery run down
completely and then recharging it around once a month.
• Please remove the battery from its mount after using your device
NOTE
Compare the local electric power supply with the connection values of the
device. Should the connection values not match, please contact
info@walser.de or phone +49 8432-9489-0.
NOTE
Only connect the power supply unit to an earthed plug.
NOTE
After use, disconnect the device from the local power supply by simply pulling out the mains plug.
32
8.

Operating the device, settings and display signals

Brightness in %
Channels
Battery level control (in
mains power operation
always showing 4 bars)
Power connection socket
round

8.1 Switching the device on/off

• Switch on the device with the on / off switch (11).
• For the function of the LED bulbs, the brightness must be set to at least 1%.
• The light is ready for use.
• After using the light, please power it off
NOTE
Please note that the lamp does not work if the batteries are not sufficiently charged or the
brightness control is set to minimum (0 %)!
8.2 Setting brightness (dimmer function)
• Switch on the device with the on / off switch (11) (if not already done)
• As standard, the dim function for the brightness level is pre-set when the lamp is switched on.
When choosing the brightness level, the corresponding field does NOT flash specially (when
selecting another function, the corresponding fields flash on the display).
• By pressing one of the multi-function buttons / rotary switches on the front or back of the lamp
(3+10), you can switch between adjusting the brightness (dim function) and colour temperature.
• Select the function for adjusting brightness.
• Turn one of the multi-function buttons/rotary switches (3+10) to set the desired brightness.
• The desired brightness is shown on the display (13).
• Immediately after turning the knob (3+10), the brightness is adjusted, saved and shown on
the display.
• The brightness can be adjusted in steps of 1% from 0 to 100 %.

8.3 Setting the colour temperature on the device

• Switch on the device with the on / off switch (11) (if not already done)
• The currently set colour temperature is shown on the display.
• By pressing the multi-function buttons / rotary knob several times, you can switch between
adjusting brightness (dim function) and colour temperature.
• Select the function for setting the colour temperature. The selected colour temperature will be
indicated by the colour temperature flashing on the display.
• The colour temperature can be set in steps of 10 Kelvin from 3,200 to 5,500 Kelvin.
• Press one of the multi-function buttons or rotary knob to set the desired colour temperature.
• The desired colour temperature is shown on the display.
• P ress one of the multi-function buttons once to confirm the desired value of the colour
temperature.
Groups (A-F)
Multifunction
push-dial back-
side
ON/OFF switch
Color temperature
in Kelvin
33