Before Starting The Equipment; Operation - Scheppach 5907902901 Originalbetriebsanleitung

Danger!
Sound and vibration
Sound and vibration values were measured in accordance
with EN 60745.
L sound pressure level
pA
K uncertainty
pA
L sound power level
WA
K uncertainty
WA
Wear ear-muffs.
The impact of noise can cause damage to hearing.
Total vibration values (vector sum of three directions)
determined in accordance with EN 60745.
Main handle
Hammer drilling in
Concrete: a = 13.59 m/s , K = 1.5 m/s
2
h(HD)
Additional handle
Hammer drilling in
Concrete: a = 11.265 m/s , K = 1.5 m/s
2
h(HD)
Main handle
Chiselling: a = 14.3 m/s , K = 1.5 m/s
2
h(CHeq)
Additional handle
Chiselling: a = 14.51 m/s
2
h(CHeq)
The specified vibration value was established in
accordance with a standardized testing method. It may
change according to how the electric equipment is used
and may exceed the specified value in exceptional
circumstances.
The specified vibration value can be used to compare
the equipment with other electric power tools.
The specified vibration value can be used for initial
assessment of a harmful effect.
Keep the noise emissions and vibrations to a
minimum.
• Only use appliances which are in perfect working
order.
• Service and clean the appliance regularly.
• Adapt your working style to suit the appliance.
• Do not overload the appliance.
• Have the appliance serviced whenever necessary.
• Switch the appliance off when it is not in use.
• Wear protective gloves.

Before starting the equipment

Before you connect the equipment to the mains supply
make sure that the data on the rating plate are identical
to the mains data.
Warning!
Always pull the power plug before making adjust-
ments to the equipment.
Check the drilling point for concealed electrical cables,
gas and water pipes using a cable/pipe detector.
Additional handle (Fig. 2 – Item 8)
For safety reasons you must only use the hammer
drill with the additional handle.
The additional handle (8) enables you to achieve better
stability whilst using the hammer drill. The machine must
14 І 64
 www.scheppach.com  service@scheppach.com  +(49)-08223-4002-99  +(49)-08223-4002-58
90.9 dB(A)
3 dB(A)
101.9 dB(A)
3 dB(A)
2
2
2
, K = 1.5 m/s
2
not be used without the additional handle (8) for safety
reasons. The additional handle (8) is secured to the
hammer drill by a clamp. Turning the handle anticlock-
wise (looking from the handle) will release the clamp.
Turning the handle clockwise will tighten the clamp. First
release the additional handle clamp. You can then swing
the additional handle (8) into the most comfortable
working position for you. Now turn the additional handle
in the opposite direction again until the additional handle
is secure.
Tiefenanschlag (Fig. 3 – Item.9)
The depth stop (9) is held in place with the locking
screw (A) on the additional handle (8) by means of a
clamp.
• Undo the locking screw (A) and fit the depth stop (9).
• Set the depth stop (9) to the same level as the drill bit.
• Pull the depth stop (9) back by the required drilling
depth.
• Retighten the locking screw (A).
• Now drill the hole until the depth stop (9) touches the
workpiece.
Tool insertion (Fig. 4)
• Clean the tool before insertion and apply a thin coa-
ting of drill bit grease to the shaft of the tool.
• Pull back and hold the locking sleeve (2).
• Insert the dust-free tool into the tool mounting as far
as it will go whilst turning it. The tool will lock itself.
• Check that it is properly secure by pulling the tool.
Tool removal (Fig. 5)
Pull back and hold the locking sleeve (2) and remove
the tool.
Dust collection device (Fig. 6)
Slide the dust collection device (B) over the drill bit
before carrying out any hammer drilling vertically above
your head.

Operation

Danger
To prevent all danger, the machine must only be
held using the two handles (5/8). Otherwise there may
be a risk of suff ering an electric shock if you drill into
cables.
Status indicator (Fig.1)
The status indicator (6) lights up when the power plug is
connected.
Switching On and Off (Fig.1)
To switch on: Press and hold the operating switch (4).
To switch off : Let go of the operating switch (4)
Button hammer drilling / chiselling (Fig. 7)
• For hammer drilling, press the button (D) on the rotary
switch (3) and simultaneously turn the rotary switch
(3) to position E.
• For chiseling, press the button (D) on the rotary switch
(3) and simultaneously turn the rotary switch (3) to
position F. In switch position F the chisel is not locked.
• For chiseling, press the button (D) on the rotary switch
(3) and simultaneously turn the rotary switch (3) to
position G. The chisel is locked in position G.
Notice!
Only low pressure is required for hammer drilling. Ex-
cessive pressure will exert an unnecessary force on the
motor. Check the drill bits at regular intervals. Sharpen
or replace blunt drill bits.