Connections; Rear Panel - JVC DT-V21G11 Bedienungsanleitung

Connections

Rear panel

1 AC IN terminal
AC power input connector. Connect the provided AC power cord
to an AC outlet.
Attach the provided power cord holder to prevent accidental
disconnection of the AC power cord. (
Caution: Do not connect the power cord until all other
connections are completed.
2 AC POWER switch
Turns AC power on or off.
You need to press
monitor after turning on the AC POWER switch.
3 REMOTE terminal
Terminal for controlling the monitor by an external control
( "External Control" on page 22).
4 VIDEO terminals (BNC)
Input (IN) and output (OUT) terminals for the composite signals.
5 COMPO. (Y, PB/B-Y, PR/R-Y) terminals (BNC)
Input (IN) and output (OUT) terminals for the analog component
(color difference) signal.
6 AUDIO (IN) terminals (pin jack)
Input terminals for the analog audio signals.
Use this terminal for the analog audio connection of the SDI.
When a superimposed signal (EMBEDDED AUDIO signal on an
SDI signal) is input, analog audio signals cannot be input.
7 AUDIO MONITOR OUT (OUT 1, OUT 2) terminals (pin jack)
Output terminals for the analog audio signal.
The terminals emit the audio signals through the AUDIO (IN)
terminal or EMBEDDED AUDIO signals through the E. AUDIO
3G SDI/HD SDI/SD SDI (IN 1 or IN 2) input terminal.
The signal is output from this terminal only when the monitor
is on or in "P.SAVE" (power save) mode (
on page 17).
Attaching the power cord holder
The provided power cord holder prevents accidental disconnection of the AC power cord from the AC IN terminal. The holder consists of two
parts: the cord case and the case cover.
1
AC IN terminal
cord case
Do not use any screws other than those supplied.
● Push the case cover into the cord case and check that the power plug is connected firmly.
8
below)
u on page 10) to use the
button (
"NO SYNC ACTION"
case cover
2
Note for connections
• Before making any connections, turn off all the equipment.
• Use a cord whose plugs correctly match the terminals on this monitor
and the equipment.
• Plugs should be firmly inserted; poor connections could cause noise.
• When unplugging a cord, be sure to grasp its plug and pull it out.
• DO NOT connect the power cord until all connections are complete.
• Refer also to the user manual of each piece of equipment.
The EMBEDDED AUDIO signal...
– is decoded into an analog signal, then emitted.
– is emitted only when "SDI 1" or "SDI 2" is selected, and when
EMBEDDED AUDIO signals come in to the E. AUDIO 3G SDI/
HD SDI/SD SDI (IN 1 or IN 2) terminal.
8 E. AUDIO 3G SDI/HD SDI/SD SDI (IN 1, IN 2) terminals (BNC)
Input terminals for the 3G SDI/HD SDI/SD SDI signals.
The terminals accept also EMBEDDED AUDIO signals including
up to 16 audio channels with a sampling frequency of 48 kHz.
Use SDI IN 1 and SDI IN 2 terminal when selecting DUAL LINK
SDI for the input.
9 E. AUDIO 3G SDI/HD SDI/SD SDI (SWITCHED OUT) terminal
(BNC)
Output terminal for the 3G SDI/HD SDI/SD SDI signals.
The SDI signals of the current input (SDI 1 or SDI 2) are re-
clocked, then emitted.
When an input other than SDI 1 and SDI 2 is selected, the
SDI signal of the input selected last time is emitted from this
terminal.
The signals are emitted from this terminal only when the
monitor is on or in "P.SAVE" (power save) mode.
No signals are emitted when DUAL LINK SDI is selected for the
input.
p DVI-D (HDCP) terminals
Input terminal for the DVI-D signal compatible with HDCP.
When the picture is not displayed correctly, change the setting
of "DVI INPUT SEL." (
3
To take off the case cover
Security slot
Attach a security wire to
this slot.
page 20)