To Play A Dvd Or Ld Recorded In Dolby Digital Or Dts Surround; Recording An Audio Source - Aiwa AV-D58 Bedienungsanleitung

TO PLAY A DVD OR LD RECORDED IN
DOLBY DIGITAL OR DTS SURROUND
This receiver is equipped with the Dolby Digital decoder and DTS
decoder, and has the digital in (both OPTICAL and COAXIAL)
terminals. When a DVD or LD player is connected to the digital in
terminal of the receiver, you can enjoy theater-quality audio right
in your home when playing discs recorded in Dolby Digital or
DTS surround.
Before operation
• Check that TAPE MONITOR or SOURCE DIRECT is not
activated.
• When connecting an LD player equipped with the AC-3 RF OUT
terminal, use an RF demodulator unit. Also connect the analog
AUDIO OUT terminals of the LD player to the receiver to play
all the sources. For further information, refer to the instructions
of the LD player.
1 Turn FUNCTION to select the VIDEO 1 (VIDEO 2)
function and press BAND/DIGITAL/ANALOG
repeatedly until "DIGITAL"(auto) is displayed.
The DVD (LD) player connected to the VIDEO 1 OPTICAL
(VIDEO 2 COAXIAL) IN terminal is selected as a source.
2 Start playing the DVD (LD) recorded in Dolby
Digital or DTS surround.
• The "DOLBY DIGITAL" indicator will light on the display when
the bit stream of the Dolby Digital surround comes in the
unit.
To select Dolby Digital surround mode according to your
speakers, see "SELECTING DOLBY SURROUND" on page
18.
• The "dts" indicator will light on the display when the bit stream
of the DTS surround comes in the unit.
To select DTS surround mode according to your speakers,
see "SELECTING DTS SURROUND" on page 22.
NOTE
• While TAPE MONITOR or SOURCE DIRECT is activated,
"DIGITAL" cannot be selected.
• When headphones are plugged in, Dolby Digital surround mode
or DTS surround mode is automatically changed to
"2chSTEREO" and the "STEREO" indicator lights on the display.
Even if SURROUND is pressed while the headphones are
plugged in, the mode cannot be changed.
• This unit supports input signals of the Dolby Digital surround
bit stream, DTS surround bit stream and linear PCM whose
sampling frequency is 32 kHz, 44.1 kHz and 48 kHz.
• When connecting some DVD players to the receiver through
the digital in terminals, noise may be heard in the DVD operation:
e.g. searching a disc, skipping a chapter.

RECORDING AN AUDIO SOURCE

1 Select the program source to be recorded.
Turn FUNCTION.
2 Set the tape deck or MD recorder to recording
mode.
3 Start the selected program source.
To monitor recorded sound during recording (when the
connected tape deck is a three-head system)
Press TAPE MONITOR. "TAPE ON" appears on the display for
four seconds, and then the source name selected in step 1 comes
back on. To cancel the tape monitor, press it again so that "TAPE
OFF" appears.
NOTE
• TAPE MONITOR is not available when the source direct function
is activated.
• Any sound control system has no effect on recording (see page
10).
• Input sound through the digital in terminals cannot be recorded.
When recording the sound from the DVD, CD, MD or LD player,
connect the analog AUDIO OUT terminals of the player to the
corresponding AUDIO IN terminals of the receiver.
The sound will be recorded in 2 ch stereo.
• When recording audio sources by the MD recorder connected
to the VIDEO 1/DVD/MD AUDIO OUT terminals, the selected
video source (see page 12) should be V2 or V3. Recording
cannot be done while the V1 (VIDEO 1) is selected and
displayed on the window.
• Input sound from the tape deck connected to the TAPE
MONITOR IN terminals cannot be recorded.
Selecting DTS digital mode
There are some audio CDs recorded in DTS surround. You
can play DTS audio CDs in the same way as DVDs, but there
may be a noise at the beginning part of the disc.
When playing DTS audio CDs, it is recommended to select
"DTS" digital mode.
1 Select "ANALOG" mode.
2 Hold down BAND/DIGITAL/ANALOG until "DTS" appears
on the display.
To restore auto "DIGITAL" mode, repeat the above so that
"DIGITAL" appears on the display.
NOTE
When selecting DTS digital mode, do not play discs
recorded in linear PCM whose sampling frequency is 96
kHz.
Otherwise there will be a noise.
En
13
ENGLISH