Inhaltsverzeichnis
Werbung
GB
3. Saging er vanskelig og skjæret er ujevnt.
•
Sagbladet er ute av stilling eller er sløvt.
Bytt ut sagbladet.
D
4. Arbeidsstykket begynner å vibrere hardt
under saging.
NL
•
Sagbladet er overopphetet eller bøyd.
Bytt ut sagbladet.
F
5. Maskinen støyer og/eller går ujevnt.
•
Børstene er slitte.
Få kundeservice til å bytte ut børstene.
E
Garanti
Garantibetingelsene gjengis på det vedlagte,
separate garantikortet.
P
I
S
FIN
N
DK
56
Accuracy
Allen key
Lubrication
Opening/closing the lock
Electrical safety
When using electric machines always observe
the safety regulations applicable in your country
to reduce the risk of fire, electric shock and per-
sonal injury. Read the following safety instructi-
ons and also the enclosed safety instructions.
Keep these instructions in a safe place!
Always check that the power supply
corres-ponds to the voltage on the
rating plate.
Class II machine - Double insulation -
You don't need any earthed plug.
Replacing cables or plugs
If the mains cable becomes damaged, it must be
replaced with a special mains cable available
from the manufacturer or the manufacturer's
customer service. Dispose of old cables or plugs
immediately after replacing them with new ones.
It is dangerous to connect the plug of a loose
cable to a socket.
Using extension cables
Only use an approved extension cable suitable
for the power input of the machine. The minimum
conductor size is 1.5 mm
2
. When using a cable
reel always unwind the reel completely.
Safety tips for the laser beamer.
•
Never look into the light beam of the laser.
•
Never point the light beam of the laser at
humans or animals.
•
Do not point the light beam of the laser at
strongly reflecting material. Hazard from
reflected light.
•
Only have repairs made to the laser beamer
by qualified personnel / professional repair
specialists.
Ferm
Ferm
•
Do not insert any hard objects into the laser
optics.
•
Clean the laser optics with a soft, dry brush.
Please keep these instructions safe!
Applications
You can use this jigsaw to cut workpieces made
of different materials (wood, aluminium, plastic,
metal, etc.) accurately and to any shape you
wish. The thickness of the workpiece must not
exceed 70 mm maximum (for wood). Any other
use (e.g. stationary operation) is expressly exclu-
ded.
The maximum sawing depth of 70 mm is only
achievable when using an extra long saw blade.
Always select a lower angle setting
when working with hard materials.
3. ASSEMBLY AND ADJUSTING
INSTRUCTIONS
Assembly instructions
Fig. 3.1-3.6
Fig. 3.1 The thickness of the material to be cut
must not exceed the maximum sawing
depth.
Fig. 3.2 Inspect the saw blade for any damage
before use and replace if necessary.
Fig. 3.3 Ensure that the workpiece to be sawed
is properly secured.
Fig. 3.4 Ensure that the workpiece to be sawed
is clean.
Fig. 3.5 Ensure that there is a sufficient gap
beneath the workpiece so that the saw
will not accidentally come in contact with
any other surfaces.
Fig. 3.6 Ensure that the material to be cut is free
from nails, screws, etc.
Inserting the saw blade
Fig. 2 and 4.1-4.4
Ensure that the plug is disconnected from the
socket outlet. To insert the saw blade, loosen the
hexagon screw (A) using the Allen key (C) (anti-
clockwise). Insert the saw blade (B) from beneath
with the teeth facing forward in the head of the
jigsaw. Tighten hexagon screw (A) using the
GB
D
NL
F
E
P
I
S
FIN
N
DK
09
Werbung
Inhaltsverzeichnis
