Rotary Hammer Safety Warnings; Additional Safety Warnings - Hitachi DH 40MC Bedienungsanleitung

ROTARY HAMMER SAFETY
WARNINGS
1. Wear ear protectors
Exposure to noise can cause hearing loss.
2. Use auxiliary handle(s), if supplied with the tool.
Loss of control can cause personal injury.
3. Hold power tool by insulated gripping surfaces,
when performing an operation where the cutting
accessory may contact hidden wiring or its own
cord.
Cutting accessory contacting a "live" wire may make
exposed metal parts of the power tool "live" and could
give the operator an electric shock.

ADDITIONAL SAFETY WARNINGS

1. Ensure that the power source to be utilized conforms
to the power requirements specifi ed on the product
nameplate.
2. Ensure that the power switch is in the OFF position.
If the plug is connected to a receptacle while the power
switch is in the ON position, the power tool will start
operating immediately, which could cause a serious
accident.
3. When the work area is removed from the power source,
use an extension cord of suffi cient thickness and rated
capacity. The extension cord should be kept as short as
practicable.
4. Do not touch the bit during or immediately after
operation. The bit becomes very hot during operation
and could cause serious burns.
5. Before starting to break, chip or drill into a wall, fl oor or
ceiling, thoroughly confi rm that such items as electric
cables or conduits are not buried inside.
6. Always hold the body handle and side handle of the
power tool fi rmly. Otherwise the counterforce produced
may result in inaccurate and even dangerous operation.
7. Wear a dust mask.
Do not inhale the harmful dusts generated in drilling or
chiseling operation. The dust can endanger the health of
yourself and bystanders.
8. Mounting the tool
○ To prevent accidents, make sure to turn the switch off
and disconnect the plug from the receptacle.
○ When using tools such as bull points, drill bits, etc.,
make sure to use the genuine parts designated by our
company.
○ Clean the shank portion of the drill bit. Then smear the
shank portion with the grease or machine oil.
9. The rotation speed cannot be changed by pressing the
rotation speed selector switch while the motor is rotating.
To change speeds, switch off the tool fi rst.
10. RCD
The use of a residual current device with a rated residual
current of 30mA or less at all times is recommended.
NAMES OF PARTS (Fig. 1 – Fig. 13)
Drill bit
1
Stopper
2
Selector lever
3
Switch trigger
4
Handle
5
Nameplate
6
Brush cap
7
(Inside the Tail cover)
Set screw (Under the
8
Tail cover)
Tail cover
9
Housing
0
Side handle
!
Grip
@
SYMBOLS
WARNING
The following show symbols used for the machine.
Be sure that you understand their meaning before
use.
DH40MC: Rotary Hammer
To reduce the risk of injury, user must read
instruction manual
Only for EU countries
Do not dispose of electric tools together with
household waste material!
In observance of European Directive 2002/96/
EC on waste electrical and electronic equipment
and its implementation in accordance with
national law, electric tools that have reached
the end of their life must be collected separately
and returned to an environmentally compatible
recycling facility.
Rated voltage
Ensure that the power source to be utilized
V
conforms to the power requirements specifi ed
on the product nameplate.
P
Power Input
n
No-load speed
0
Bpm Full-load impact rate
φ
Drilling diameter, max.
max
Weight
(According to EPTA-Procedure 01/2003)
kg
Drill bit
Core bit
Adjustment of the tool position function
Hammering only function
Rotation and hammering function
9
English
Front cap
#
Grease
$
Wing bolt
%
Taper shank adapter
^
Drill bit (Taper shank)
&
Cotter
*
Core bit shank
(
Core bit
)
Guide plate
q
Center pin
w
Core bit tip
e
Carbon brush
r