Inhaltsverzeichnis
Werbung
Verfügbare Sprachen
Verfügbare Sprachen
English
ROTARY HAMMER SAFETY WARNINGS
1.
Wear ear protectors.
Exposure to noise can cause hearing loss.
2.
Use auxiliary handle(s), if supplied with the tool.
Loss of control can cause personal injury.
3.
Hold power tool by insulated gripping surfaces, when
performing an operation where the cutting accessory
may contact hidden wiring or its own cord. Cutting
accessory contacting a "live" wire may make
exposed metal parts of the power tool "live" and
could give the operator an electric shock.
SPECIFICATIONS
1
Voltage (by areas)*
Power input
Capacity
2
No load speed*
Full-load impact rate*
2
Weight (without cord, side handle)
*
1
Be sure to check the nameplate on product as it is subject to change by areas.
*
2
With constant velocity regulator
STANDARD ACCESSORIES
(1) Case (Molded plastic) ................................................. 1
(2) Side Handle ................................................................. 1
(3) Stopper ........................................................................ 1
(4) Hammer Grease A ...................................................... 1
Standard accessories are subject to change without
notice.
OPTIONAL ACCESSORIES (sold separately)
Through-hole drilling (Rotation + Hammering)
(1) Drill bit (hexagon shank)
Overall length: 280, 400, 505 mm
External dia.: 16, 19, 22, 25, 28, 32, 38 mm
Anchor hole drilling (Rotation + Hammering)
(3) Cotter
(1) Drill bit (taper shank)
External dia.: 11, 12, 14.3,
14.5, 17.5,
21.5 mm
7
(2) Taper shank
adapter
4.
Do not touch the bit during or immediately after
operation. The bit becomes very hot during
operation and could cause serious burns.
5.
Before starting to break, chip or drill into a wall, floor
or ceiling, thoroughly confirm that such items as
electric cables or conduits are not buried inside.
6.
Always hold the body handle and side handle of the
power tool firmly. Otherwise the counterforce
produced may result in inaccurate and even
dangerous operation.
7.
Wear a dust mask
Do not inhale the harmful dusts generated in drilling
or chiseling operation. The dust can endanger the
health of yourself and bystanders.
(110V, 115V, 120V, 127V, 220V, 230V, 240V)
950 W*
Drill bit: 40 mm
Core bit: 120 mm
510 min
2800 min
6.5 kg
Taper shank
Application drill bit
adapter
Morse taper
Drill bit (taper shank)
(No. 1)
11, 12, 14.3, 14.5, 17.5 mm
Morse taper
Drill bit (tape shank)
(No. 2)
21.5 mm
Taper shank adapter formed A-
A-taper
taper or B-taper is provided as
optional accessory, but drill bit for
B-taper
it is not provided.
Large dia. hole boring (Rotation + Hammering)
(1) Center
(Guide
pin
plate)
(1) Center pin
Applied to core bits from 38 mm to 105 mm
Applied to core bits 32 mm and 35 mm
NOTE
Do not use core bits 25 mm or 29 mm.
(2) Core bit
External dia. 25, 29, 32, 35, 38, 45, 54, 64, 79, 94,
105 mm
(with guide plate, not applicable to cores 25 mm or
29 mm)
(3) Core bit shank
Applied to core bits above 38 mm
Applied to core bits below 35 mm
Anchor work (for self-anchors)
1
–1
–1
(2) Core
(3) Core bit
shank
bit
Werbung
Inhaltsverzeichnis
