Description Of The Programming Menu - Saeco Office One Bedienungsanleitung

11.3

Description of the programming menu

1. Program. menu
Password Insert password
1.1. Identifi cation 1.1.1.Admin/Filial PIN
Default 00000
1.1.2. Model
1.1.3. Version
1.1.4. Point of sale:
Default 00000
1.2. Setup 1.2.1. Std temperature
Default: 100°C
1.2.2. Prog. doses
1.2.3. Pre-brewing
Default: Medium
1.2.4. Rinsing
Default: No
1.2.5. Descaling
1.2.6. Filter warning
Default: No
1.2.7. Credits
1.2.8. Payment syst
1.2.9.Language
Default: English
1.2.10. Coffee fi lter
Default: No
1.2.11. Dreg delay
Default: 15
Installation of the machine - Service Provider Manual
Press ENTER to access Programming menu mode
Default value: Enter the previously entered and stored password (4 digits) to access the program-
Default: 0000 ming menu.
The Service Provider's or the Administrator's code are identifi ed by: a numerical
value between 0 and 65535. In versions equipped with Tag Reader, this code is
compared to that on the labels on the capsule boxes. Credit loading will be enabled
only if this code and the code reported in section 2.9.1 correspond to those on the
label.
(Read only) It identifi es the appliance model.
(Read only) It identifi es the appliance software version.
It identifi es the sale point: Numerical value from 0 to 65535. Enter the selected
number. This number will then be displayed.
Boiler working temperature (expressed in centigrade degrees) when the appliance
is "ready" to work. range: 90-105.
1.2.2.1. Short prod. dose Product short quantity (it's a numerical parameter without physical equivalent, e.g.
Default: 130 cc)
1.2.2.2. Medium prod. dose Product medium quantity (this is a numerical parameter without any physical equiv-
Default: 180 alent, e.g. cc).
1.2.2.3. Long prod. dose Product long quantity (it's a numerical parameter without physical equivalent, e.g.
Default: 400 cc)
Pre-brewing time:
No, Short, Medium, Long.
Yes enables rinsing process: The process starts when the boiler reaches the ready
temperature after appliance power on.
This process starts only if the boiler temperature is lower than 50°C at the power
on of the appliance
1.2.5.1. Water hardness
Range 0-4.
Default: 1
0 disables descaling check function. With hardness 1, 2, 3 and 4 the descaling
check function is enabled and the alarm appears after about 120, 90, 60, 30 litres
respectively (Values from 5 to 9 will not be accepted).
1.2.5.2. Descalc. warning
Yes enable descaling alarm signal on display
Default: Yes
Yes enable softener fi lter cleaning message on display. When activated the alarm
appears after about ca. 60 lt., in any case after 60gg.
1.2.7.1 Credit check (Read Only)
Yes: Appliance working by checking the remaining credits
No: No credits check is enabled
1.2.7.2 Credit warning
"Yes" enables:
Default: Yes
- display of the credit alarm on reaching the minimum preset credit quantity;
- display of the "no credit" alarm, when credits have been used up.
1.2.7.3 Load credits Number of credits to insert:
Default: 000 Range 0 - 256
1.2.8.1 Enable system
Yes enables payment system use.
Default: No
This function can be enabled only if the appliance is provided with a PCB for step-
per coin slot management.
1.2.8.2 Display credit
Yes enables credit display of the stepper coin slot.
Default: No
This function can be enabled only if the appliance is provided with a PCB for step-
per coin slot management.
Select the language to use.
Yes enables fi lter coffee function.
Only "esc" button will dispense fi lter coffee. The fi lter operation is not available.
Exhausted capsules reset waiting time expressed in seconds (with dreg drawer
removed) when relative warning or alarm is present. After this time the warning or
the alarm is reset
Range: 0-255 seconds.
• 43 •