Maintenance - Smeg KSEV 910 X1 Montageanweisung Und Gebrauchsanweisung

Maintenance

ATTENTION! Before performing any maintenance operation,
isolate the hood from the electrical supply by switching off at
the connector and removing the connector fuse.
Or if the appliance has been connected through a plug and
socket, then the plug must be removed from the socket.
Cleaning
The cooker hood should be cleaned regularly (at least with the
same frequency with which you carry out maintenance of the
fat filters) internally and externally. Clean using the cloth
dampened with neutral liquid detergent. Do not use abrasive
products. DO NOT USE ALCOHOL!
Warning:
Failure to carry out the basic cleaning recommendations of the
cooker hood and replacement of the filters may cause fire
risks.
Therefore, we recommend oserving these instructions.
The manufacturer declines all responsibility for any damage to
the motor or any fire damage linked to inappropriate
maintenance or failure to observe the above safety
recommendations.
Grease filter
Fig. 2
This must be cleaned once a month (or when the filter
saturation indication system – if envisaged on the model in
possession – indicates this necessity) using non aggressive
detergents, either by hand or in the dishwasher, which must
be set to a low temperature and a short cycle.
When washed in a dishwasher, the grease filter may discolour
slightly, but this does not affect its filtering capacity.
To remove the grease filter B, pull the spring release handle.
Charcoal filter (filter version only)
Fig. 3
It absorbs unpleasant odours caused by cooking.
The charcoal filter can be washed once every two months (or
when the filter saturation indication system – if envisaged on
the model in possession – indicates this necessity) using hot
water and a suitable detergent, or in a dishwasher at 65°C (if
the dishwasher is used, select the full cycle function and leave
dishes out).
Eliminate excess water without damaging the filter, then
remove the mattress located inside the plastic frame and put it
in the oven for 10 minutes at 100° C to dry completely.
Replace the mattress every 3 years and when the cloth is
damaged.
Remove the filter holder frame by turning the knobs (g) 90°
that affix the chimney to the cooker hood.
Insert the pad (i) of activated carbon into the frame (h) and fit
the whole back into its housing (j).
It is possible to use a traditional carbon filter,
washable nor regenerable, to be replaced every 3 - 4 months.
The filter holder frame of the carbon filter is welded together;
the eventual frame supplied with the hood is not, therefore, to
be used.
Insert it into its housing and fix it turning the 2 plastic knobs.
Replacing lamps
Disconnect the hood from the electricity.
Warning! Prior to touching the light bulbs ensure they are
cooled down.
For models shown in Fig. 1E + Fig. 4E:
1. Press on the lamp cover and release to open.
2. Replace the damaged light bulb.
Only use halogen bulbs of 20W max (G4), making sure
you do not touch them with your hands.
3. Close the lamp cover (it will snap shut).
For models shown in Fig. 1N/O + Fig. 4N/O:
1. Unscrew the lamp cover.
2. Replace the damaged light bulb.
Only use halogen bulbs of 20W max (G4), making sure
you do not touch them with your hands.
3. Refit the lamp cover.
For models shown in Fig.1+Fig.4
(A/B/C/D/F/H/I/K/P/Q/S/T/U/V):
1. Extract the lamp cover by levering it off with a small
screwdriver or similar tool.
2. Replace the damaged light bulb.
Only use halogen bulbs of 20W max (G4), making sure
you do not touch them with your hands.
3. Close the lamp cover (it will snap shut).
For models shown in Fig. 1J + Fig. 4J:
1. Use a small screwdriver as a lever on the borders of the
lamp in order to remove the lightbulb.
2. Unthread the connector „a".
3. Slide out the lightbulb to be replaced and replace with a
new 12V 20W 30° Ø35 12V GU4 PHILIPS STANDARD
LINE code 425409.
4. Carry out the replacement and mount the new lightbulb by
following instructions in the reverse.
For models shown in Fig. 1G + Fig. 5G:
Dismount the chimneys: remove the two screws (20 a)
that attaches the upper chimney to the support „G" (Fig.
16).
Remove the box „q": remove the screw „r" that secures
the cooker hood.
Remove the lamp housing „s": remove the screws „t"
that position the housing in the lamp housing area.
Extract the damaged lamp.
Use only PHILIPS type 14515 (GX 5.3) 12V - 75W
halogen bulbs..
Reposition and secure the lamp housing „s" and the box
„q" and remount the chimneys.
For models shown in Fig. 1K + Fig. 4K:
Certain versions of this cooker hood provide for an
incandescent lamp at 40W maximum (E14), remove the
lamp cover to access the lamp housing and carry out any
replacements.
Only for the illustrated model in Fig. 1L + Fig. 6L:
1. Open the front panel "v" upwards, which holds the lamp in
neither
place, ensuring to hold the lamp "z" with one hand.
2. Replace the damaged lamp with one of identical technical
characteristics.
Attention! To guarantee the equivalent quality of lighting,
it is recommended to use the same type of lamp bulb:
23